Wyo. Code R. 053-0008-7
OSHA - Construction 1926
Chapter 7: Signs, Signals & Barricades (G)
Effective Date: 07/29/2005 to 04/25/2018
Rule Type: Superceded Rules & Regulations
Reference Number: 053.0008.7.07292005
| 1926.200 | Accident prevention signs and tags. |
|---|---|
| 1926.201 | Signaling. |
| 1926.202 | Barricades. |
| 1926.203 | Definitions applicable to this subpart. |
AUTHORITY: Sec. 107, Contract Work Hours and Safety Standards Act (Construction Safety Act) (40 U.S.C. 333); secs. 4, 6, 8, Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), or 3-200 (65 FR 50017) as applicable, 29CFR part 1911.
(a) General. Signs and symbols required by this subpart shall be visible at all times when work is being performed, and shall be removed or covered promptly when the hazards no longer exist.
(1) Danger signs (see Figure G-1) shall be used only where an immediate hazard exists.
(2) Danger signs shall have red as the predominating color for the upper panel; black outline on the borders; and a white lower panel for additional sign wording.
(1) Caution signs (see Figure G-2) shall be used only to warn against potential hazards or to caution against unsafe practices.
(2) Caution signs shall have yellow as the predominating color; black upper panel and borders: yellow lettering of 'caution' on the black panel; and the lower yellow panel for additional sign wording. Black lettering shall be used for additional wording.
Figure G-1
Figure G-2
(d) Exit signs. Exit signs, when required, shall be lettered in legible red letters, not less than 6 inches high, on a white field and the principal stroke of the letters shall be at least three-fourths inch in width.
(e) Safety instruction signs. Safety instruction signs, when used, shall be white with green upper panel with white letters to convey the principal message. Any additional wording on the sign shall be black letters on the white background.
(f) Directional signs. Directional signs, other than automotive traffic signs specified in paragraph (g) of this section, shall be white with a black panel and a white directional symbol. Any additional wording on the sign shall be black letters on the white background.
(1) Construction areas shall be posted with legible traffic signs at points of hazard.
(2) All traffic control signs or devices used for protection of construction workmen shall conform to Part VI of the Manual of Uniform Traffic Control Devices (AMUTCD), 1988 Edition, Revision 3, September 3 1993, FHWA-SA-94-027 or Part VI of the Manual on Uniform Traffic Control Devices, Millennium Edition, December 2000, FHWA, which are incorporated by reference. The Director of the Federal Register approves this incorporation by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may obtain a copy of the Millennium Edition from the following organizations: American Traffic Safety Services Association, 15 Riverside Parkway, Suite 100, Fredericksburg, VA 22406-1022; Telephone: 1-800-231-3475; FAX: (504)-368-1722; www.atssa.com; Institute of Transportation Engineers, 1099 14th Street, NW., Suite 300 West, Washington, DC 20005-3438; FAX: (202) 289-7722; www.ite.org; and American Association of State Highway and Transportation Officials; www.aashto.org; Telephone: 1-800-231-3475; FAX: 1-800-525-5562. Electronic copies of the MUTCD 2000 are available for downloading at http://mutcd.fhwa.dot.gov/kno-millennium. Electronic copies of the 1988 Edition MUTCD, Revision 3, are available for downloading at http://www.osha.gov/doc/highway_workzones. Both documents are available for inspection at the OSHA Docket Office, Room N2625, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210 or at the Office of the Federal Register, 800 North Capitol Street, NW., Suite 700, Washington, DC.
(1) Accident prevention tags shall be used as a temporary means of warning employees of an existing hazard, such as defective tools, equipment, etc. They shall not be used in place of, or as a substitute for, accident prevention signs.
(2) Specifications for accident prevention tags similar to those in Table G-1 shall apply.
Table G-1
| DO NOT OPERATE | DANGER | CAUTION | OUT OF ORDER DO NOT USE |
|---|---|---|---|
| White tag - White letters on a red square | White tag - White letters on red oval with a black square | Yellow tag - Yellow letters on a black background | White tag - White letters on a black background |
| Basic Stock (Background) | Safety Colors (Ink) | Copy Specification (Letters) | |
| White | Red | Do Not Operate | |
| White | Black and Red | Danger | |
| Yellow | Black | Caution | |
| White | Black | Out of Order Do Not Use |
(i) Additional rules. American National Standards Institute (ANSI) Z35.1-1968, Specifications for Accident Prevention Signs, and Z35.2-1968, Specifications for Accident Prevention Tags, contain rules which are additional to the rules prescribed in this section. The employer shall comply with ANSI Z35.1-1968 and Z35.2-1968 with respect to rules not specifically prescribed in this subpart.
(a) Flaggers. Signaling by flaggers and the use of flaggers, including warning garments worn by flaggers shall conform to Part VI of the Manual on Uniform Traffic Control Devices, (1988 Edition, Revision 3 or the Millennium Edition), which are incorporated by reference in § 1926.200(g)(2).
(b) Crane and hoist signals. Regulations for crane and hoist signaling will be found in applicable American National Standards Institute standards.
Barricades for protection of employees shall conform to Part VI of the Manual on Uniform Traffic Control Devices (1988 Edition, Revision 3 or the Millennium Edition), which are incorporated by reference in § 1926.200(g)(2).
(a) 'Barricade' means an obstruction to deter the passage of persons or vehicles.
(b) 'Signs' are the warnings of hazard, temporarily or permanently affixed or placed, at locations where hazards exist.
(c) 'Signals' are moving signs, provided by workers, such as flaggers, or by devices, such as flashing lights, to warn of possible or existing hazards.
(d) 'Tags' are temporary signs, usually attached to a piece of equipment or part of a structure, to warn of existing or immediate hazards.
This page has been intentionally left blank.