PURPOSE: This rule describes general requirements and guidelines for obtaining an approved Metallic Minerals Waste Management Area Permit and the relationship of this permit to the requirements of other environmental programs.

1. (1) To comply with the Metallic Minerals Waste Management Act, sections 444.352– 444.380, RSMo Supp. 1989 and to ensure that metallic mineral wastes are contained in an environmentally safe manner, the operator of a metallic minerals waste management area must obtain approval of a method of closure and an inspection-maintenance plan following closure.

2. (2) Consistent with sections 444.362 and 444.365, RSMo Supp. 1989, the requirements of applicable state environmental programs and permits shall be included in the closure and inspection-maintenance plans. Compliance with these requirements will be considered a condition of the Metallic Minerals Waste Management Permit. Existing environmental programs, permits, statutes and rules include, but are not limited to:

   1. (A) The Water Pollution Control Program’s—

      1. 1. National Pollutant Discharge

Elimination System (NPDES) Permit, Chapter 644, RSMo and 10 CSR 20-6.010;

1. 2. 401/404 approvals, Federal Clean

Water Act and section 401, RSMo;

1. 3. Land application letters of approval

Chapter 644, RSMo; and

1. 4. Underground Injection Control (UIC)

Permit, Chapters 577 and 644, RSMo, 10 CSR 20-6.070 and 10 CSR 20-6.090;

1. (B) The Division of Geology and Land Survey’s Dam and Reservoir Safety—

   1. 1. Registration Permit, section 236.440,

RSMo and 10 CSR 22-3.030;

1. 2. Construction Permit, section

236.435, RSMo and 10 CSR 22-3.040; and

1. 3. Safety Permit, section 236.440,

RSMo and 10 CSR 22-3.050;

1. (C) The Solid Waste Management Program’s—

   1. 1. Solid Waste Disposal Area Permit,

sections 260.200—260.245, RSMo and 10 CSR 80-1.010—10 CSR 80-4.010;

1. 2. Solid Waste Processing Facility

Permit, sections 260.200–260.245, RSMo, 10 CSR 80-1.010, 10 CSR 80-2.020 and 10 CSR 80-5.010; and

1. 3. Waste Tire Requirements, section

206.200–206.345, RSMo and 10 CSR 80- 8.020–10 CSR 80-8.060;

1. (D) The Air Pollution Control Program’s—

   1. 1. Major and Minor Source Permits,

section 643.075, RSMo and 10 CSR 10- 6.060;

1. 2. De minimis Permit, section 643.075,

RSMo and 10 CSR 10-6.060; and

1. 3. Open Burning Permit, Chapter 643,

RSMo and, 10 CSR 10-2.100, 10 CSR 10- 3.030, 10 CSR 10-4.090, 10 CSR 10-5.070 and 10 CSR 10-6.060;

1. (E) The Public Drinking Water Program’s permit to construct and permit to dispense drinking water, sections 640.110.1 and 640.115, RSMo and 10 CSR 60-10.010 and 10 CSR 60-3.010;
2. (F) The Land Reclamation Program’s permit to engage in surface mining and sections 444.500—444.786, RSMo; and

3. (G) The Hazardous Waste Management Program’s—

   1. 1. Hazardous Waste Generator Notifica-

tion Requirements, section 260.380, RSMo and 10 CSR 25-5;

1. 2. Hazardous Waste Resource Recovery

Certification, section 260.350–260.434, RSMo and 10 CSR 25-9; and

1. 3. Hazardous Waste Facility Permit,

section 260.350, RSMo and 10 CSR 25. (3) If it is determined that existing environmental laws and regulations are not adequate to achieve the objectives of the closure and inspection-maintenance plans, the director may establish additional permit conditions as may be necessary to achieve those objectives, taking cost, benefit and technical feasibility into account.

1. (4) The definitions, provisions and guidelines in 10 CSR 45 shall be used with and, in case of conflict, shall take precedence over other regulations listed in section (2) of this rule.

AUTHORITY: section 444.380, RSMo Supp. 1999.* Original rule filed Oct. 2, 1990, effective April 29, 1991. Amended: Filed Jan. 19, 2000, effective Sept. 30, 2000.

*Original authority: 444.380, RSMo 1989, amended 1993, 1995.