1. A. The Tax Commission provides a standard Vehicle Identification Number (VIN) plate for vehicles, snowmobiles, trailers, and outboard boat motors that have never had a distinguishing number or if the original VIN has been altered, removed, or defaced.
2. B. The owner of the unit will make application to the Tax Commission on form TC-162 for an assigned or replacement VIN. In the event the applicant has no title to the unit, the Motor Vehicle Division follows the procedure in Rule R873-22M-2, to determine ownership.

3. C. The vehicle may be subject to inspection and investigation. Upon determination of the validity of the application, a vehicle identification plate is issued.

   1. 1. In cases involving vehicles where the original plate has been removed or obliterated but the original factory number can be verified, a VIN plate is issued with the original VIN entered by means of an approved procedure.
   2. 2. In all other instances a prestamped VIN plate is issued bearing an official Utah assigned VIN.

   3. 3. The VIN plate must, under the supervision of the Tax Commission, be attached to the unit as follows:

      1. (1) primary location is on a portion of the left front door lock post;

      2. (2) secondary location is on a portion of the firewall, either left or right side, whichever is most advantageous; (This location is to be selected only when the VIN plate cannot be attached to the lock posts.)

         b) motorcycles, snowmobiles, and outboard motors:

      3. (1) as near as possible to the original number location; (If an original number, the VIN plate shall be affixed to the headstock.)

         c) trailers:

      4. (1) primary location is on a portion of the right side of the tongue or drawbar near the body;

      5. (2) secondary location is on a portion of the metal frame near the front right corner;

         d) on units where it is not practical to install rivets, the VIN plate may be attached by adhesive only.

      a) passenger and commercial vehicles:

4. D. The Motor Vehicle Division is responsible for the control, security, and distribution of the VIN plates and will keep the necessary records and require regular reports from designated branch offices.

5. E. Following are the specifications of the official Utah assigned identification plate and attachment accessories.

   1. 1. Size will be 1 inch x 3 inches x .003 inch deep etched to .002 inch with 1/8 inch radius corners.
   2. 2. Material will be color anodized aluminum foil.
   3. 3. Color will be blue background with silver lettering.
   4. 4. Backing will be laminated with permanent pressure sensitive adhesive.
   5. 5. Control numbers will be serialized with 1/8 inch permanent embossed or anodized numbers.
   6. 6. The state seal will be in the left center, with appropriate rivet areas designated.

   7. 7. The assigned number will be prestamped using the prefix of "UT." The number series to include one letter and five digits with the letter to identify the unit type as follows:

      TABLE

      a) Passenger and Commercial P00001

      b) Motorcycles M00001

      c) Trailers T00001

      d) Reconstructed vehicle R00001

      e) Outboard Motors E00001

      f) Snowmobiles S00001

KEY: taxation, motor vehicles, aircraft, license plates

Date of Last Change: January 25, 2026

Notice of Continuation: November 9, 2021

Authorizing, and Implemented or Interpreted Law: 41-1a-102; 41-1a-104; 41-1a-108; 41-1a-116; 41-1a-211; 41-1a-215; 41-1a-214; 41-1a-401; 41-1a-402; 41-1a-411; 41-1a-413; 41-1a-414; 41-1a-416; 41-1a-418; 41-1a-419; 41-1a-420; 41-1a-421; 41-1a-422; 41-1a-522; 41-1a-701; 41-1a-1001; 41-1a-1002; 41-1a-1004; 41-1a-1005; 41-1a-1009 through 41-1a-1011; 41-1a-1101; 41-1a-1209; 41-1a-1211; 41-1a-1220; 41-6-44; 53-8-205; 59-12-104; 59-2-103; 72-10-109 through 72-10-112; 72-10-102