No tire of a type and size designation specified in Table I of Appendix A that is designed for use on passenger cars and manufactured on or after October 1, 1972, but does not conform to all the requirements of this standard, shall be sold, offered for sale, introduced or delivered for introduction in interstate commerce, or imported into the United States, for any purpose.

The following tables list tire sizes and tire constructions with proper load and inflation values. The tables group tires of related constructions and load-inflation values. Persons requesting the addition of new tire sizes to the tables or the addition of tables for new tire constructions may, when the additions requested are compatible with existent groupings, or when adequate justification for new tables exists, submit five copies of information and data supporting the request to the Secretary of Transportation, Attention: Motor Vehicle Programs, National Highway Traffic Safety Administration, U.S. Department of Transportation, Washington, D.C. 20590.

The information should contain the following:

1. (1) The tire size designation, and a statement either that the tire is an addition to a category of tires listed in the tables or that it is in a new category for which a table has not been developed.
2. (2) The tire dimensions, including aspect ratio, size factor, section width, overall width and test rim size.
3. (3) The load-inflation schedule of the tire.
4. (4) A statement as to whether the tire size designation and load-inflation schedule has been coordinated with the Tire and Rim Association, the European Tyre and Rim Technical Organisation, the society of Manufacturers and Traders Limited, the Japan Automobile Tire Manufacturers Association, the Deutsche Industrie Norm and the Scandinavian Tire and Rim Organisation.
5. (5) Copies of test data sheets showing test conditions, results and conclusions obtained for individual tests specified in this chapter.

6. (6) Justification for the additional tire sizes.

   FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 109
   TABLE I-A
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR CONVENTIONAL AND LOW SECTION HEIGHT BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim width	Minimum size	Section width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	factor (inches)	(inches)
   6.00-13 …	770	820	860	900	930	970	1,010	1,040	1,080	1,110	1,140	4	29.37	6.00
   6.50-13 …	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	30.75	6.60
   7.00-13 …	980	1,030	1,080	1,130	1,180	1,230	1,270	1,310	1,360	1,400	1,440	5	31.88	7.10
   6.00-14 …	840	900	930	980	1,020	1,060	1,100	1,130	1,170	1,210	1,240	4	30.64	6.10
   6.45-14 …	860	910	960	1,000	1,010	1,080	1,120	1,160	1,200	1,240	1,260	4½	30.92	6.60
   6.50-14 …	930	990	1,030	1,080	1,130	1,170	1,210	1,250	1,300	1,330	1,370	4	31.75	6.60
   6.95-14 …	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,310	1,350	1,390	5	31.96	7.00
   7.00-14 …	1,030	1,100	1,140	1,190	1,240	1,200	1,310	1,380	1,430	1,470	1,520	5	32.88	7.10
   7.25-14 …	1,040	1,100	1,160	1,210	1,260	1,310	1,360	1,400	1,450	1,490	1,540	5	32.92	7.30
   7.50-14 …	1,150	1,230	1,280	1,340	1,390	1,450	1,500	1,550	1,600	1,650	1,700	5½	34.19	7.65
   7.75-14 …	1,150	1,210	1,270	1,330	1,390	1,440	1,500	1,550	1,600	1,650	1,690	5½	34.09	7.75
   8.00-14 …	1,240	1,320	1,380	1,440	1,500	1,560	1,620	1,670	1,730	1,780	1,830	6	35.17	8.10
   8.25-14 …	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,670	1,730	1,780	1,830	6	35.11	8.20
   8.50-14 …	1,330	1,420	1,480	1,550	1,610	1,670	1,740	1,790	1,850	1,910	1,960	6	35.91	8.35
   8.55-14 …	1,360	1,430	1,510	1,580	1,640	1,710	1,770	1,830	1,890	1,950	2,000	6	36.06	8.50
   8.85-14 …	1,430	1,510	1,580	1,660	1,730	1,790	1,860	1,920	1,990	2,050	2,100	6½	36.82	8.95
   9.00-14 …	1,430	1,510	1,580	1,660	1,730	1,790	1,860	1,920	1,990	2,050	2,100	6½	36.91	8.80
   9.50-14 …	1,540	1,640	1,700	1,780	1,850	1,930	2,000	2,060	2,130	2,200	2,260	6½	37.74	9.05
   6.00-15 …	890	940	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4	31.64	6.10
   6.50-15 …	980	1,040	1,080	1,130	1,180	1,230	1,270	1,320	1,360	1,400	1,440	4½	32.75	6.60
   6.70-15 …	1,110	1,190	1,230	1,290	1,340	1,400	1,450	1,500	1,550	1,590	1,640	4½	33.95	7.00
   6.85-15 …	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,390	5	32.48	6.90
   7.00-15…	1,170	1,240	1,310	1,380	1,450	1,515	1,580	1,640	1,700	1,760	1,820	1,870	1,930	5	36.02	7.35
   7.10-15 …	1,190	1,270	1,320	1,380	1,440	1,500	1,550	1,600	1,660	1,710	1,760	5	34.89	7.40
   7.35-15 …	1,070	1,130	1,180	1,240	1,290	1,340	1,390	1,440	1,480	1,530	1,570	5½	33.86	7.50
   7.60-15 …	1,310	1,400	1,450	1,520	1,580	1,640	1,710	1,760	1,820	1,800	1,930	5½	36.05	7.90
   7.75-15 …	1,150	1,210	1,270	1,330	1,380	1,440	1,190	1,540	1,590	1,640	1,690	5½	34.53	7.65
   8.00-15 …	1,380	1,470	1,530	1,600	1,670	1,730	1,800	1,860	1,920	1,980	2,040	6	36.84	8.30
   8.15-15 …	1,240	1,300	1,370	1,430	1,490	1,550	1,610	1,660	1,720	1,770	1,820	6	35.50	8.15
   8.20-15 …	1,470	1,570	1,630	1,710	1,780	1,860	1,920	1,980	2,050	2,110	2,170	6	37.50	8.50
   8.25-15…	1,030	1,190	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,670	1,730	1,780	1,830	6	35.57	8.20
   8.45-15 …	1,340	1,410	1,480	1,550	1,620	1,680	1,740	1,800	1,860	1,920	1,970	6	36.37	8.35
   8.55-15…	1,220	1,290	1,360	1,430	1,510	1,580	1,640	1,710	1,770	1,830	1,890	1,950	2,000	6	36.57	8.45
   8.85-15 …	1,430	1,510	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	37.29	8.80
   8.90-15 …	1,700	1,810	1,880	1,970	2,050	2,130	2,210	2,290	2,360	2,430	2,500	6½	39.54	9.30
   9.00-15 …	1,460	1,540	1,620	1,690	1,760	1,830	1,900	1,970	2,030	2,090	2,150	6	37.45	8.50
   9.15-15 …	1,510	1,600	1,680	1,750	1,830	1,900	1,970	2,030	2,100	2,160	2,230	6½	37.92	9.05
   5.00-16…	715	765	815	860	910	975	990	1,030	1,070	1,110	1,150	1,185	1,220	3	31.03	5.15
   6.00-16 …	1,075	1,135	1,195	1,250	1,300	1,350	1,400	1,450	1,500	…	4	34.17	6.25
   6.50-16…	1,090	1,150	1,215	1,280	1,345	1,405	1,465	1,525	1,580	1,635	1,690	1,740	1,790	4½	35.59	6.80
   6.70-16 …	1,185	1,240	1,300	1,355	1,410	1,465	1,525	1,580	1,635	1,690	1,740	1,795	4½	35.60	7.40
   7.00-16 …	1,365	1,440	1,515	1,585	1,650	1,715	1,780	1,840	1,900	…	5	37.02	7.35
   7.50-16 …	1,565	1,650	1,735	1,810	1,890	1,960	2,035	2,105	2,175	…	5½	38.78	8.00
   6.50-17 …	1,215	1,275	1,330	1,390	1,450	1,500	1,560	1,620	1,680	1,740	1,795	1,850	5	37.00	7.60
   L84-15 …	1,510	1,600	1,680	1,750	1,830	1,900	1,970	2,030	2,100	2,160	2,230	6	37.88	8.65

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the "dash".

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-B
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim width	Minimum size	Section width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	factor (inches)	(inches)
   A70-13…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	5½	30.27	7.30
   B70-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	5	30.86	7.35
   C70-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5½	31.68	7.80
   D70-13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.34	8.00
   D70-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.81	7.85
   E70-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.45	8.05
   F70-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	5½	34.16	8.30
   G70-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.18	8.75
   H70-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	36.19	9.10
   J70-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	36.87	9.50
   L70-14…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6½	37.62	9.75
   A70-15…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	30.99	6.60
   C70-15…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,390	5½	32.75	7.50
   D70-15…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	33.37	7.70
   E70-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	6	34.13	8.10
   F70-15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6	34.89	8.35
   G70-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.66	8.60
   H70-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	36.64	8.95
   J70-15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	37.36	9.35
   K70-15…	1,290	1,380	1,460	1,540	1,620	1,690	1,770	1,830	1,900	1,970	2,030	2,090	2,150	6½	37.66	9.40
   L70-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6½	38.09	9.60

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-C
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   “Super Balloon” Sizes
   4.80-10…	320	355	390	430	470	490	510	535	555	575	595	…	3½	23.90	5.00
   5.20-10…	350	395	440	485	530	555	575	605	625	650	670	695	715	3½	24.84	5.20
   5.20-10…	385	430	475	515	550	580	605	630	650	675	700	…	4	24.00	5.80
   5.20-12…	395	445	495	545	595	625	655	685	710	735	760	785	810	3½	26.79	5.20
   5.60-12…	460	520	575	620	670	715	760	795	825	855	885	915	940	4	27.83	5.71
   5.90-12…	460	505	550	595	640	665	700	730	735	785	810	…	4	26.00	5.90
   6.20-12…	505	555	605	655	705	735	775	805	835	865	895	…	4½	27.00	6.30
   5.20-13…	430	485	540	590	640	670	710	740	765	795	820	850	875	3½	27.72	5.20
   5.60-13…	495	560	620	675	725	770	810	850	880	910	945	975	1,005	4	28.92	5.71
   5.90-13…	555	625	695	755	815	860	895	935	970	1,005	1,040	1,075	1,105	4	29.74	5.91
   6.20-13…	520	580	640	700	750	780	820	850	880	910	945	…	4½	28.00	6.30
   6.40-13…	630	705	785	845	915	945	985	1,025	1,060	1,100	1,140	1,175	1,210	4½	31.26	6.42
   6.70-13…	690	775	860	935	1,000	1,045	1,090	1,135	1,175	1,220	1,260	1,305	1,340	4½	32.14	6.69
   6.90-13…	695	745	795	845	915	955	1,005	1,045	1,085	1,120	1,160	…	5	30.00	7.20
   5.20-14…	475	535	595	645	695	735	785	825	855	885	915	945	975	3½	28.89	5.20
   5.60-14…	530	595	660	715	770	815	855	890	920	955	990	1,020	1,050	4	29.94	5.71
   5.90-14…	585	660	730	785	850	880	925	970	1,005	1,040	1,080	1,115	1,145	4	30.76	5.91
   6.40-14…	660	745	825	890	960	1,000	1,050	1,090	1,130	1,170	1,210	1,250	1,290	4½	32.19	6.42
   6.45-14 …	860	910	960	1,000	1,040	1,080	1,120	…	4½	30.92	6.60
   5.20-15…	505	570	630	685	740	780	830	870	900	935	965	1,000	1,030	3½	29.75	5.20
   5.60-15…	555	625	695	755	815	860	895	935	970	1,005	1,040	1,075	1,105	4	30.87	5.71
   5.90-15…	615	695	770	825	890	935	980	1,015	1,070	1,090	1,130	1,165	1,200	4	31.77	5.91
   6.40-15 …	875	950	1,010	1,055	1,100	1,150	1,190	1,230	1,260	…	4½	33.20	6.42
   “Low Section” Sizes
   5.00-12…	370	420	465	505	540	565	580	605	625	650	670	695	715	3½	25.62	5.04
   5.50-12…	415	470	520	560	605	635	665	695	720	745	770	800	820	4	26.93	5.59
   6.00-12…	485	545	605	655	705	735	785	815	845	875	905	935	965	4½	28.33	6.14
   5.00-13…	410	460	510	545	585	610	635	660	685	710	735	755	780	3½	26.64	5.04
   5.50-13…	445	495	550	595	640	670	710	740	765	795	820	850	875	4	27.95	5.59
   7.25-13…	730	825	915	990	1,070	1,110	1,160	1,200	1,245	1,290	1,335	1,380	1,420	5	32.51	7.24
   7.50-13…	775	875	970	1,040	1,120	1,180	1,225	1,270	1,315	1,365	1,410	1,460	1,500	5½	33.22	7.48
   5.50-15L…	505	570	630	675	725	760	800	840	870	900	935	965	995	4	29.97	5.59
   6.00-15L…	595	665	740	800	860	890	930	970	1,005	1,040	1,080	1,115	1,145	4½	31.29	6.14
   6.50-15L…	675	755	840	900	970	1,010	1,060	1,105	1,145	1,185	1,230	1,270	1,305	4½	32.66	6.54
   7.00-15L…	760	855	950	1,025	1,100	1,145	1,190	1,235	1,280	1,325	1,375	1,420	1,460	5	33.85	7.01
   “Super Low Section” Sizes
   145-10/5.95-10…	380	430	475	515	550	580	605	630	650	675	700	725	745	4	24.76	5.79
   125-12/5.35-12…	335	380	420	450	485	510	535	550	570	590	610	630	650	3½	24.68	5.00
   135-12/5.65-12…	370	420	465	505	540	570	590	620	640	665	690	710	730	4	25.53	5.39
   145-12/5.95-12…	440	495	550	595	640	665	700	730	755	785	810	840	865	4	26.69	5.79
   155-12/6.15-12…	485	545	605	655	705	735	775	805	835	865	895	925	950	4½	27.36	6.18
   135-13/5.65-13…	415	470	520	555	595	625	655	685	710	735	760	785	810	4	26.53	5.39
   145-13/5.95-13…	470	525	585	620	670	705	745	770	800	825	855	885	910	4	27.61	5.79
   155-13/6.15-13	515	575	610	700	750	780	820	850	880	910	945	975	1,005	4½	28.44	6.18
   165-13/6.45-13…	575	645	715	770	825	865	905	935	970	1,005	1,040	1,075	1,105	4½	29.52	6.57
   175-13/6.95-13…	635	715	795	845	915	955	1,005	1,045	1,085	1,120	1,160	1,200	1,235	5	30.34	7.01
   185-13/7.35-13…	695	785	870	945	1,010	1,060	1,115	1,160	1,205	1,245	1,290	1,335	1,370	5½	31.41	7.40
   135-14/5.65-14…	440	495	550	595	640	665	700	730	755	785	810	840	865	4	27.54	5.59
   145-14/5.95-14…	495	560	620	665	715	750	785	815	845	875	905	935	965	4	28.54	5.79
   155-14/6.15-14…	540	610	675	730	780	825	860	895	925	960	995	1,030	1,060	4½	29.45	6.18
   125-15/5.35-15…	395	445	495	535	570	600	625	650	675	700	720	745	770	3½	27.69	5.00
   135-15/5.65-15…	460	520	575	610	660	690	720	750	775	805	835	860	885	4	28.53	5.39
   145-15/5.95-15…	520	585	650	710	760	790	830	860	890	925	955	985	1,015	4	29.54	5.79
   155-15/6.35-15…	585	660	730	780	835	875	915	950	985	1,020	1,055	1,090	1,125	4½	30.45	6.18
   175-15/7.15-15…	705	795	880	955	1,020	1,070	1,125	1,170	1,215	1,255	1,300	1,345	1,385	5	32.42	7.01
   165-14…	650	715	770	815	880	925	970	1,000	1,035	1,080	1,115	1,145	1,170	4½	31.22	6.57
   175-14…	715	780	850	915	980	1,025	1,070	1,115	1,160	1,200	1,235	1,270	1,310	5	32.13	7.01
   185-14…	805	870	940	1,000	1,080	1,135	1,190	1,235	1,290	1,325	1,370	1,400	1,435	5½	33.15	7.40
   195-14…	860	950	1,025	1,105	1,180	1,235	1,290	1,345	1,400	1,445	1,490	1,535	1,580	5½	34.18	7.80
   205-14…	940	1,025	1,115	1,190	1,270	1,335	1,400	1,455	1,510	1,565	1,610	1,655	1,700	6	34.84	8.19
   215-14…	1,015	1,115	1,200	1,290	1,380	1,445	1,520	1,590	1,640	1,700	1,740	1,785	1,830	6	35.75	8.58
   225-14…	1,080	1,180	1,280	1,380	1,465	1,540	1,620	1,700	1,750	1,810	1,850	1,915	1,970	6½	36.69	8.98
   165-15…	685	750	805	860	915	970	1,015	1,060	1,105	1,135	1,180	1,200	1,235	4½	31.73	6.57
   185-15…	815	905	970	1,050	1,115	1,180	1,235	1,280	1,325	1,370	1,410	1,445	1,490	5½	33.59	7.40
   195-15…	880	970	1,050	1,135	1,215	1,280	1,335	1,390	1,445	1,490	1,535	1,580	1,620	5½	34.61	7.80
   205-15…	970	1,060	1,145	1,225	1,300	1,370	1,445	1,500	1,565	1,610	1,665	1,720	1,765	6	35.79	8.19
   215-15…	1,050	1,145	1,235	1,335	1,435	1,500	1,590	1,640	1,700	1,740	1,800	1,850	1,910	6	37.24	8.58
   235-15…	1,150	1,295	1,435	1,545	1,660	1,735	1,825	1,895	1,965	2,035	2,110	2,180	2,245	6½	38.26	9.37
   5.0-15…	460	520	575	610	660	690	720	750	775	805	835	860	885	4	28.53	5.39
   5.5-15…	520	585	650	710	760	790	830	860	890	925	955	985	1,015	4	29.54	5.79

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-D
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR DASH(-) RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   145-10…	495	525	545	565	585	605	625	640	655	670	685	700	710	4	24.76	5.79
   125-12…	405	430	445	465	480	495	505	525	535	550	560	575	580	3½	24.68	5.00
   135-12…	480	510	530	550	565	585	600	620	635	650	665	675	685	4	25.53	5.39
   145-12…	570	605	625	650	675	695	715	740	760	775	790	805	815	4	26.69	5.79
   155-12…	630	670	695	720	745	770	795	820	840	860	875	890	905	4½	27.36	6.18
   135-13…	515	545	565	590	610	630	650	670	690	705	715	730	740	4	26.53	5.39
   145-13…	605	640	665	695	720	740	765	790	815	830	845	855	870	4	27.61	5.79
   155-13…	670	710	735	765	790	815	840	870	895	910	925	940	955	4½	28.44	6.18
   165-13…	700	750	800	850	890	930	970	1,010	1,050	1,090	1,130	1,170	1,200	4½	29.52	6.57
   175-13 …	810	860	920	980	1,040	1,100	1,150	1,200	1,240	1,300	1,350	4½	30.30	6.75
   185-13 …	870	940	1,010	1,080	1,140	1,210	1,270	1,330	1,390	1,450	1,510	5	31.42	7.25
   195-13 …	970	1,040	1,110	1,180	1,250	1,320	1,400	1,450	1,520	1,580	1,640	5½	32.38	7.70
   135-14…	555	585	610	635	655	675	695	720	740	750	765	780	790	4	27.54	5.39
   145-14…	645	680	710	735	760	785	810	840	865	885	905	920	935	4	28.54	5.79
   155-14…	630	680	720	760	800	840	880	920	950	980	1,010	1,040	1,070	4½	29.45	6.18
   165-14…	740	790	840	890	940	980	1,020	1,060	1,100	1,140	1,180	1,220	1,250	4½	30.53	6.57
   175-14 …	830	900	960	1,030	1,100	1,160	1,230	1,280	1,350	1,400	1,470	5	31.63	7.00
   185-14 …	920	1,000	1,070	1,140	1,220	1,290	1,360	1,420	1,500	1,560	1,640	5	32.59	7.30
   195-14 …	1,020	1,100	1,180	1,270	1,340	1,420	1,500	1,570	1,650	1,720	1,800	5½	33.69	7.80
   205-14 …	1,100	1,180	1,270	1,380	1,350	1,540	1,620	1,700	1,770	1,860	1,940	6	34.82	8.80
   215-14 …	1,200	1,300	1,390	1,510	1,580	1,670	1,770	1,850	1,920	2,010	2,100	6	35.79	8.60
   225-14 …	1,320	1,420	1,510	1,610	1,710	1,800	1,900	1,970	2,050	2,150	2,230	6½	36.44	8.95
   125-15…	495	525	545	565	585	605	625	640	655	670	685	700	710	3½	27.69	5.00
   135-15…	585	620	645	670	695	715	735	755	775	795	810	825	840	4	28.53	5.39
   145-15…	680	720	750	780	805	830	855	875	895	920	940	960	975	4	29.54	5.79
   155-15…	740	785	815	850	880	905	930	955	980	1,005	1,025	1,045	1,060	4½	30.45	6.18
   165-15…	770	820	870	920	970	1,020	1,070	1,110	1,150	1,190	1,230	1,270	1,310	4½	31.45	6.57
   175-15 …	990	1,050	1,100	1,150	1,200	1,250	1,300	1,350	1,400	1,440	1,480	5	32.41	7.00
   180-15…	925	980	1,020	1,060	1,095	1,130	1,170	1,190	1,230	1,260	1,280	1,305	1,325	4½	32.04	6.62
   185-15 …	1,000	1,070	1,140	1,210	1,280	1,350	1,420	1,480	1,540	1,600	1,660	5½	33.58	7.45
   195-15 …	1,080	1,160	1,240	1,330	1,400	1,470	1,550	1,620	1,680	1,760	1,820	5½	34.22	7.65
   205-15 …	1,190	1,280	1,370	1,450	1,530	1,620	1,700	1,760	1,840	1,920	2,000	6	35.20	8.10
   215-15 …	1,280	1,380	1,480	1,570	1,660	1,760	1,860	1,940	2,020	2,100	2,200	6	36.00	8.35
   220-15 …	1,320	1,420	1,520	1,610	1,695	1,785	1,875	1,960	2,050	2,135	2,225	6	36.49	8.35
   225-15 …	1,370	1,470	1,580	1,670	1,780	1,880	1,980	2,060	2,150	2,240	2,340	6½	36.94	8.80
   230-15 …	1,405	1,515	1,625	1,725	1,825	1,925	2,020	2,110	2,190	2,280	2,360	6½	37.30	8.80
   235-15 …	1,430	1,540	1,640	1,750	1,850	1,960	2,060	2,160	2,250	2,350	2,450	6½	37.75	9.05
   240-15 …	1,455	1,570	1,680	1,790	1,890	1,990	2,090	2,190	2,280	2,380	2,480	6½	38.28	9.05
   185-16 …	1,140	1,210	1,270	1,330	1,390	1,450	1,500	1,550	1,600	1,650	1,700	5½	34.14	7.40
   165-400…	800	860	920	980	1,030	1,080	1,130	1,180	1,220	1,260	1,300	1,340	1,380	4.65	32.04	6.62

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-E
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “77 SERIES” BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   G77-14 …	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.04	8.45
   5.9-10…	385	430	475	515	550	580	605	630	660	675	700	…	4	24.00	5.80
   5.9-12…	460	505	550	595	640	665	700	730	755	785	810	…	4	26.00	5.90
   6.2-12…	485	545	605	655	705	735	775	805	835	865	895	925	950	4	27.21	6.06
   6.2-13…	515	575	640	700	750	780	820	850	880	910	945	975	1,005	4	28.19	6.06
   6.5-13…	575	645	715	770	825	865	905	935	970	1,005	1,040	1,075	1,105	4½	29.18	6.54
   6.9-13…	635	715	795	845	915	955	1,005	1,045	1,085	1,120	1,160	…	4½	29.92	6.77
   6.2-15…	585	660	730	780	835	875	915	950	985	1,020	1,055	1,090	1,125	4	30.17	6.06
   6.9-15…	705	795	880	955	1,020	1,070	1,125	1,170	1,215	1,255	1,300	1,345	1,385	4½	31.93	6.77

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-F
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR TYPE “R” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   5.20R10…	435	460	485	510	535	560	585	615	635	660	685	710	735	3½	24.84	5.20
   5.00R12…	480	495	515	535	555	575	595	615	635	650	670	690	710	3½	25.62	5.04
   5.20R12…	515	540	565	590	615	640	665	695	715	740	765	790	815	3½	26.79	5.20
   5.50R12…	520	545	570	595	620	650	670	705	725	750	775	800	825	4	26.93	5.59
   5.60R12…	600	630	655	685	715	740	770	800	825	850	875	905	930	4	27.83	5.71
   5.00R13…	535	555	575	590	615	630	650	670	690	705	725	745	765	3½	26.64	5.04
   5.20R13…	570	595	620	645	670	695	720	750	770	795	820	845	870	3½	27.72	5.20
   5.50R13…	575	600	625	650	675	695	725	750	775	795	825	850	875	4	27.95	5.59
   5.60R13…	655	685	710	740	765	795	825	855	880	905	935	960	990	4	28.92	5.71
   6.00R13…	675	705	735	760	790	815	845	875	900	925	950	975	1,005	4	29.37	6.00
   5.90R13…	705	780	805	830	860	885	915	940	965	990	1,015	1,045	1,070	4	29.74	5.91
   6.40R13…	810	840	870	905	940	970	1,005	1,040	1,070	1,100	1,135	1,165	1,200	4½	31.26	6.42
   6.50R13…	800	830	860	890	925	960	995	1,030	1,060	1,090	1,120	1,150	1,180	4½	30.75	6.60
   6.70R13…	690	775	860	935	1,000	1,045	1,090	1,135	1,175	1,220	1,260	1,305	1,340	4½	32.14	6.69
   7.00R13…	870	910	950	985	1,025	1,060	1,100	1,145	1,175	1,215	1,255	1,295	1,335	5	31.88	7.10
   7.25R13…	940	980	1,020	1,060	1,100	1,135	1,175	1,215	1,255	1,290	1,330	1,370	1,410	5	32.51	7.24
   5.20R14…	605	640	670	700	730	760	795	830	855	885	915	950	980	3½	28.89	5.20
   5.90R14…	750	785	815	845	875	905	935	970	995	1,025	1,055	1,085	1,115	4	30.76	5.91
   7.00R14…	925	960	1,000	1,040	1,075	1,115	1,155	1,195	1,235	1,270	1,320	1,350	1,380	5	32.88	7.10
   7.50R14…	1,065	1,100	1,140	1,180	1,220	1,260	1,300	1,340	1,380	1,415	1,460	1,500	1,540	5½	34.19	7.65
   5.60R15…	705	780	805	830	860	885	915	940	965	990	1,015	1,045	1,070	4	30.87	5.71
   6.40R15…	885	925	965	1,005	1,040	1,080	1,120	1,160	1,200	1,235	1,275	1,310	1,350	4½	33.26	6.42
   6.70R15…	975	1,015	1,055	1,095	1,130	1,170	1,215	1,255	1,290	1,325	1,365	1,405	1,445	4½	33.95	7.00
   7.60R15…	1,160	1,200	1,245	1,285	1,325	1,370	1,415	1,465	1,500	1,535	1,575	1,610	1,655	5½	36.00	7.90

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-G
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   AR70-13…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	5	30.04	7.15
   BR70-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	5½	31.04	7.60
   CR70-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	31.65	7.85
   DR70-13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.29	8.05
   CR70-14…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5½	32.23	7.65
   DR70-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.78	7.90
   ER70-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.42	8.10
   FR70-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6	34.34	8.55
   GR70-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.12	8.85
   HR70-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6½	36.31	9.40
   JR70-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	36.86	9.55
   LR70-14…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6½	37.59	9.80
   DR70-15…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	33.34	7.75
   ER70-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.91	7.95
   FR70-15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6	34.87	8.40
   GR70-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.65	8.65
   HR70-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6½	36.83	9.20
   JR70-15…	1,260	1,350	1,430	1,500	1,580	1,660	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	37.31	9.40
   KR70-15…	1,290	1,380	1,460	1,540	1,620	1,690	1,770	1,830	1,900	1,970	2,030	2,090	2,150	6½	37.62	9.50
   LR70-15…	1,340	1,430	1,520	1,600	1,680	1,760	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6½	38.06	9.65
   MR70-15…	1,420	1,520	1,610	1,700	1,780	1,860	1,940	2,020	2,090	2,160	2,230	2,300	2,370	7	38.93	10.15

   ¹ The letters “HR”, “SR” or “VR” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-H
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR TYPE “R” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   145R10…	465	495	525	550	580	605	630	655	680	700	725	750	770	4	24.76	5.79
   125R12…	370	400	430	450	475	495	515	535	555	575	595	610	630	3½	24.68	5.00
   135R12…	440	475	505	535	560	585	610	635	655	680	700	725	745	4	25.53	5.39
   145R12…	530	565	600	635	665	695	725	755	780	810	835	860	885	4	26.69	5.79
   155R12…	590	630	665	700	735	770	800	835	865	895	925	950	980	4½	27.36	6.18
   135R13…	480	515	545	575	600	630	655	680	705	730	755	780	800	4	26.53	5.39
   145R13…	590	630	665	700	735	770	800	835	860	890	920	950	980	4	27.59	5.79
   155R13…	645	690	730	770	810	845	885	915	950	985	1,015	1,045	1,075	4½	28.44	6.18
   165R13…	680	730	770	820	860	900	930	970	1,010	1,040	1,080	1,110	1,140	4½	29.18	6.40
   175R13…	790	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	30.30	6.75
   185R13…	870	930	980	1,030	1,080	1,130	1,180	1,230	1,270	1,310	1,360	1,400	1,440	5	31.42	7.25
   195R13…	955	1,010	1,060	1,110	1,170	1,220	1,280	1,320	1,370	1,420	1,470	1,510	1,550	5½	32.38	7.70
   135R14…	515	550	585	615	645	675	705	730	760	785	810	835	860	4	27.54	5.39
   145R14…	595	635	675	715	750	785	815	850	880	910	940	965	995	4	28.54	5.79
   155R14…	690	740	780	820	860	900	940	970	1,010	1,040	1,080	1,110	1,140	4	29.51	6.05
   165R14…	760	810	860	910	960	1,000	1,040	1,080	1,120	1,160	1,200	1,240	1,270	4½	30.65	6.55
   175R14…	840	900	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,310	1,350	1,390	5	31.63	7.00
   185R14…	920	980	1,040	1,100	1,160	1,210	1,260	1,310	1,360	1,400	1,450	1,490	1,540	5	32.59	7.30
   195R14…	1,020	1,090	1,150	1,210	1,270	1,330	1,390	1,440	1,500	1,550	1,600	1,650	1,690	5½	33.69	7.80
   205R14…	1,110	1,190	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,670	1,730	1,780	1,830	6	34.82	8.30
   215R14…	1,210	1,290	1,360	1,430	1,510	1,580	1,640	1,710	1,770	1,830	1,890	1,950	2,000	6	35.79	8.60
   225R14…	1,270	1,350	1,430	1,510	1,580	1,660	1,730	1,790	1,860	1,920	1,990	2,050	2,100	6½	36.44	8.95
   125R15…	460	490	520	550	575	605	630	655	680	705	725	745	770	3½	27.69	5.00
   135R15…	545	580	615	650	680	715	745	775	800	830	855	880	910	4	28.53	5.39
   145R15…	640	680	720	760	795	830	865	900	935	965	995	1,025	1,055	4	29.54	5.79
   155R15…	690	735	780	825	865	905	940	980	1,015	1,050	1,085	1,115	1,150	4½	30.45	6.18
   165R15…	770	820	870	910	960	1,000	1,050	1,090	1,130	1,170	1,200	1,240	1,270	4½	31.18	6.40
   175R15…	840	900	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,390	5	32.30	6.90
   185R15…	950	1,010	1,070	1,130	1,180	1,240	1,290	1,340	1,390	1,440	1,480	1,530	1,570	5½	33.58	7.45
   195R15…	1,020	1,090	1,150	1,210	1,270	1,330	1,380	1,440	1,490	1,540	1,590	1,640	1,690	5½	34.22	7.65
   205R15…	1,100	1,170	1,240	1,300	1,370	1,430	1,490	1,550	1,610	1,660	1,720	1,770	1,820	6	35.20	8.10
   215R15…	1,190	1,270	1,340	1,410	1,480	1,550	1,620	1,680	1,740	1,800	1,860	1,920	1,970	6	36.00	8.35
   225R15…	1,270	1,350	1,430	1,510	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	36.94	8.80
   235R15…	1,340	1,430	1,510	1,600	1,680	1,750	1,830	1,900	1,970	2,030	2,100	2,160	2,230	6½	37.75	9.05
   206R16…	1,100	1,170	1,240	1,300	1,370	1,430	1,490	1,550	1,610	1,660	1,720	1,770	1,820	6	36.52	8.19

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-J
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “78 SERIES” BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   A78-13…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	29.74	6.60
   B78-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	5	30.72	7.05
   C78-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5½	31.56	7.45
   D78-13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.18	7.70
   A78-14…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	30.31	6.45
   B78-14…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	31.04	6.65
   C78-14…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	31.95	7.05
   D78-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5	32.52	7.35
   E78-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.29	7.65
   F78-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	5½	34.04	7.90
   G78-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.02	8.35
   H78-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	36.06	8.70
   J78-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6	36.58	8.80
   A78-15…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	30.85	6.35
   C78-15…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	32.45	6.95
   D78-15…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5	33.05	7.15
   E78-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5	33.65	7.35
   F78-15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	5½	34.56	7.70
   G78-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	5½	35.36	8.05
   H78-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	36.50	8.55
   J78-15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6	37.02	8.70
   L78-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6	37.73	8.85
   N78-15…	1,500	1,600	1,700	1,790	1,880	1,970	2,050	2,130	2,210	2,280	2,360	2,430	2,500	7	39.50	9.80

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-K
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   A60-13…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	5½	30.00	7.85
   B60-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	6	30.95	8.35
   C60-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6	31.58	8.60
   D60-13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	6	32.20	8.85
   B60-14…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	5½	31.26	8.00
   C60-14…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6	32.09	8.45
   D60-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	6	32.72	8.65
   E60-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	7	33.69	9.30
   F60-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	7	34.44	9.55
   G60-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	7	35.23	9.85
   H60-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	7	36.20	10.25
   J60-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	7	36.70	10.45
   L60-14…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	8	37.83	11.10
   B60-15…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	5½	31.85	7.80
   C60-15…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6	32.66	8.25
   E60-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	6	33.83	8.70
   F60-15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6½	34.75	9.40
   G60-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	7	35.73	9.70
   H60-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	7	36.70	10.05
   J60-15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	7	37.20	10.25
   L60-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	7	37.91	10.50

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-L
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” CANTILEVERED SIDEWALL TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   E50C-16 …	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	3½	33.31	7.95
   F50C-16 …	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,500	1,610	1,650	1,700	3½	34.04	8.20
   G50C-17 …	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	3½	35.34	8.45
   H50C-17 …	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	3½	36.30	8.80
   L50C-18 …	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	3½	38.00	9.10

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-M
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “78 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   AR78-13…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	29.55	6.50
   BR78-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	30.31	6.75
   CR78-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	31.13	7.15
   AR78-14…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	30.08	6.40
   BR78-14…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	30.84	6.60
   CR78-14…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	31.67	7.00
   DR78-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5	32.26	7.20
   ER78-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5	32.86	7.40
   FR78-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	5½	33.78	7.85
   GR78-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	34.78	8.30
   HR78-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	35.77	8.60
   JR78-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	36.47	8.95
   AR78-15…	720	770	810	860	900	940	980	1,020	1,060	1,090	1,130	1,160	1,200	4½	30.66	6.25
   BR78-15…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	31.38	6.45
   CR78-15…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	5	32.24	6.85
   ER78-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.58	7.45
   FR78-15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	5½	34.28	7.70
   GR78-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.30	8.15
   HR78-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	6	36.23	8.45
   JR78-15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	6½	36.98	8.80
   KR78-15…	1,290	1,380	1,460	1,540	1,620	1,690	1,770	1,830	1,900	1,970	2,030	2,090	2,150	6	37.03	8.70
   LR78-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	6½	37.66	9.00
   MR78-15…	1,420	1,520	1,610	1,700	1,780	1,860	1,940	2,020	2,090	2,160	2,230	2,300	2,370	6½	38.35	9.20
   NR78-15…	1,500	1,600	1,700	1,790	1,880	1,970	2,050	2,130	2,210	2,280	2,360	2,430	2,500	7	39.17	9.71

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-N
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   155/70R13…	630	650	665	685	705	725	740	760	780	800	820	835	855	4	27.17	5.93
   155/70R15…	690	710	730	750	770	790	810	830	850	870	890	910	930	4	29.20	5.93

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-O
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “LOW SECTION” TYPE “R” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   140R12…	490	520	550	580	610	640	660	690	710	740	770	4	26.20	5.40
   150R12…	570	610	640	670	700	730	760	790	820	850	880	4	27.19	5.75
   150R13…	600	640	680	720	750	780	810	840	870	900	940	4	28.17	5.75
   160R13…	670	700	740	780	820	860	900	940	980	1,010	1,040	4½	29.23	6.25
   170R13…	720	760	800	840	880	920	960	1,000	1,00	1,080	1,110	5	30.08	6.60
   150R14…	640	670	710	750	780	820	860	900	940	970	1,000	4	29.16	5.75
   180R15…	920	970	1,020	1,070	1,120	1,170	1,230	1,280	1,330	1,380	1,430	5	32.97	6.85

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-P
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR SERIES 45 CANTILEVERED SIDEWALL TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   G45C-16…	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	5	35.53	9.70

   ¹ The letter “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-R
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   CR60-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6	31.58	8.60
   DR60-14…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	6	32.72	8.65
   ER60-14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	6½	33.50	9.10

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-S
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   235/60R13…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	6	32.81	9.05

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-T
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “70 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   205/70R13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	32.29	8.05
   205/70R14…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.42	8.10
   215/70R14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6	34.34	8.55
   225/70R14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.12	8.85
   195/70R15…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	5½	33.34	7.75
   205/70R15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	5½	33.91	7.95
   215/70R15…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	6	34.87	8.40
   225/70R15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	6	35.65	8.65

   ¹ The letter “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-U
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “60 SERIES” CANTILEVERED TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   B60C-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	4½	30.41	7.65
   C60C-15…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	4	31.92	7.35

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-V
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” BIAS PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   B50-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	6	30.84	9.15
   C50-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6½	3 .48	9.40
   D50-13…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	6½	32.29	9.85
   F50-14…	1,020	1,090	1,160	1,220	1,280	1,340	1,400	1,450	1,500	1,550	1,610	1,650	1,700	7	34.10	10.20
   G50-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,690	1,730	1,780	1,930	8	35.29	10.95
   H50-14…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	8	36.24	11.35
   M50-14…	1,420	1,520	1,616	1,700	1,780	1,860	1,940	2,020	2,090	2,160	2,230	2,300	2,370	9	38.51	12.55
   N50-14…	1,500	1,600	1,700	1,790	1,880	1,970	2,050	2,130	2,210	2,280	2,360	2,430	2,500	9	39.17	12.85
   F50-15…	950	1,010	1,070	1,130	1,190	1,240	1,300	1,350	1,400	1,440	1,490	1,540	1,580	6½	33.74	9.50
   G50-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	7	35.38	10.35
   H50-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	8	36.76	11.15
   L50-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,830	1,900	1,970	2,040	2,100	2,170	2,230	8	31.94	11.65
   N50-15…	1,500	1,600	1,700	1,790	1,880	1,970	2,050	2,130	2,210	2,280	2,360	2,430	2,500	9	39.65	12.65

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-W
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   BR50-13…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	6½	30.84	9.15
   CR50-13…	840	890	950	1,000	1,050	1,100	1,140	1,190	1,230	1,270	1,320	1,360	1,400	6½	31.48	9.40
   GR50-14…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	8	35.29	10.95
   JR50-14…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	8	36.74	11.60
   GR50-15…	1,100	1,180	1,250	1,310	1,380	1,440	1,500	1,560	1,620	1,680	1,730	1,780	1,830	7	35.38	10.35
   HR50-15…	1,200	1,290	1,360	1,440	1,510	1,580	1,650	1,710	1,770	1,830	1,890	1,950	2,010	8	36.76	11.15
   JR50-15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,780	1,860	1,920	1,980	2,040	2,100	8	37.24	11.35
   LR50-15…	1,340	1,430	1,520	1,600	1,680	1,750	1,820	1,900	1,970	2,040	2,100	2,170	2,230	8	37.94	11.65

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to or in place of the “dash”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-X
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “50 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   195/50R15…	650	690	730	770	810	850	890	920	955	990	1,020	1,050	1,080	6	30.16	7.91
   225/50R16…	880	940	1,000	1,060	1,110	1,160	1,210	1,255	1,300	1,345	1,390	1,435	1,475	6½	33.34	8.98
   285/50R15…	1,260	1,350	1,430	1,500	1,580	1,650	1,720	1,790	1,860	1,920	1,980	2,040	2,100	8	36.84	11.26
   265/50R16…	1,160	1,235	1,310	1,385	1,450	1,520	1,580	1,645	1,709	1,765	1,820	1,875	1,930	8	36.55	10.71

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-Y
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR ALL MILLIMETRIC “65 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   195/65R350…	815	860	905	950	990	1,030	1,070	1,115	1,155	1,195	1,235	1,275	1,315	105	30.70	7.48
   205.65R375…	920	970	1,020	1,070	1,120	1,170	1,220	1,265	1,310	1,355	1,400	1,445	1,490	105	32.65	7.76

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-AA
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “P/80” ISO TYPE TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   P155/80R13 3…	660	705	740	760	795	825	860	880	905	935	960	980	1,005	4½	28.46	6.18

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “80”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   ³ The letters “D” for diagonal and “B” for belted may be used in place of the “R”.

   TABLE I-BB
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “40 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   285/40R15…	890	950	1,010	1,070	1,120	1,170	1,220	1,270	1,320	1,360	1,410	1,450	1,490	9½	37.42	11.22

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-CC
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “35 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   345-35R15…	960	1,030	1,090	1,150	1,210	1,270	1,320	1,370	1,420	1,470	1,520	1,560	1,610	11½	37.42	13.58

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-DD
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “55 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   205/55R16…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	6	32.57	8.19
   225/55R13…	830	890	940	980	1,030	1,080	1,120	1,160	1,200	1,240	1,280	1,320	1,350	6	30.98	8.78

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-EE
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “45 SERIES” RADIAL PLY TIRES

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   235/45R15…	780	840	890	930	980	1,030	1,070	1,110	1,150	1,190	1,230	1,270	1,300	8	32.11	9.29

   ¹ The letters “H”, “S” or “V” may be included in any tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   TABLE I-FF
   

   TIRE LOAD RATINGS, TEST RIMS, MINIMUM SIZE FACTORS, AND SECTION WIDTHS FOR “P/70 SERIES” ISO TYPE TIRES, STANDARD LOAD

   	Maximum tire loads (pounds) at various cold inflation pressures (p.s.i.)	Test rim	Minimum	Section
   		width	size factor	width 2
   Tire size designation 1	16	18	20	22	24	26	28	30	32	34	36	38	40	(inches)	(inches)	(inches)
   P20570R13 3…	870	925	980	1025	1070	1115	1155	1200	1235	1280	1310	1345	1390	5½	31.73	7.99

   ¹ The letters “H”, “S” or “V” may be included in any specified tire size designation adjacent to the “R”.

   ² Actual section width and overall width shall not exceed the specified section width by more than 7 percent.

   ³ The letters “D” for diagonal and “B” for belted may be used in place of the “R”.

   FEDERAL MOTOR VEHICLE
   SAFETY STANDARD NO. 109
   

   TABLE II—MINIMUM BREAKING ENERGY VALUES (INCH-POUNDS)
   TABLE II—A—FOR BIAS PLY TIRES WITH SIZE DESIGNATION OF 6.00 INCHES (OR 155 MILLIMETERS) AND ABOVE AND 70 SERIES TIRES

   Cord	Maximum permissible inflation pressure
   material	32 lb/in2	36 lb/in2	40 lb/in2	300 KPa
   Rayon…	1,650 in-lbs	2,574 in-lbs	3,300 in-lbs	1,650 in-lbs
   Nylon or polyester…	2,600 in-lbs	3,900 in-lbs	5,200 in-lbs	2,600 in-lbs

   TABLE II—B—FOR BIAS PLY TIRES WITH SIZE DESIGNATION
   BELOW 6.00 INCHES (OR 155 MILLIMETERS)

   Cord	Maximum permissible inflation pressure
   material	32 lb/in2	36 lb/in2	40 lb/in2	300 KPa
   Rayon…	1,000 in-lbs	1,875 in-lbs	2,500 in-lbs	1,000 in-lbs
   Nylon or polyester…	1,950 in-lbs	2,925 in-lbs	3,900 in-lbs	1,950 in-lbs

   TABLE II—C—FOR RADIAL PLY TIRES

   Size	Maximum permissible inflation pressure
   designation	32 lb/in2	36 lb/in2	40 lb/in2	300 KPa
   Below 160 millimeters…	1,950 in-lbs	2,925 in-lbs	3,900 in-lbs	1,950 in-lbs
   160 millimeters or above…	2,600 in-lbs	3,900 in-lbs	5,200 in-lbs	2,600 in-lbs

   TABLE III—TEST INFLATION PRESSURES
   Maximum permissible inflation pressure [(in pounds per square inch)]…	32 lb/in2	36 lb/in2	40 lb/in2	300 KPa
   Pressure [(in pounds per square inch)] to be used in tests for physical dimensions, bead unseating, tire strength and tire endurance…	24 lb/in2	28 lb/in2	32 lb/in2	180 KPa
   Pressure [(in pounds per square inch)] to be used in test or high speed performance…	30 lb/in2	34 lb/in2	38 lb/in2	220 KPa