1. (1) A solid waste is a hazardous waste if it is listed in this section, unless it has been excluded from this list under section 370.3(a) and (b) of this Title. Note:

   Note:

   Although the names used for chemicals in this list include common names, trade names and specific isomer names under various chemical naming systems, where any one of these previous names are used, all other equivalent names shall be considered to be listed.

2. (2) The commissioner will indicate the basis for listing the classes or types of wastes listed in this section by employing one or more of the following hazard codes: Appendix 22, infra, identifies the constituent which caused the commissioner to list the waste as a toxicity characteristic waste (E) or toxic waste (T) in subdivisions (b) and (c) of this section.

   Ignitable waste (I)

   Corrosive waste (C)

   Reactive waste (R)

   Toxicity characteristic waste (E)

   Acute hazardous waste (H)

   Toxic waste (T)

3. (3) Each hazardous waste listed in this section is assigned an EPA hazardous waste number which precedes the name of the waste. This number must be used in complying with the notification requirements of section 3010 of the Resource Conservation and Recovery Act and certain recordkeeping and reporting requirements under Parts 372, 373 and 376 (see section 370.1[e] of this Title).

4. (4) The following hazardous wastes listed in subdivision (b) of this section are subject to the exclusion limits for acutely hazardous waste established in section 371.1(f) of this Part: EPA hazardous waste numbers F020, F021, F022, F023, F026 and F027.

   (b) Hazardous waste from nonspecific sources.

5. (1) The following solid wastes are listed hazardous wastes from nonspecific sources unless they are excluded under section 370.3(a) and (c) of this Title and listed in Appendix 24, infra:

   Industry and
   EPA hazardous		Hazard
   waste number	Hazardous waste	code
   Generic:
   F001	The following spent halogenated solvents used in degreasing: tetrachloroethylene, trichloroethylene, methylene chloride, 1,1, 1-trichloroethane, carbon tetrachloride, and chlorinated fluorocarbons; all spent solvent mixtures/blends used in degreasing containing, before use, total of 10 percent or more (by volume) of one or more of the above halogenated solvents or those solvents listed in F002, F004 and F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.	(T)
   F002	The following spent halogenated solvents: tetrachloro-ethylene, methylene chloride, trichloroethylene, 1,1,1-trichloroethane, chlorobenzene, 1,1,2-trichloro-1,2,2- trifluoroethane, orthodichlorobenzene, trichlorofluoromethane and 1,1,2-trichloroethane; all spent solvent mixtures/blends containing, before use, a total of 10 percent or more (by volume) of one or more of the above halogenated solvents or those listed in F001, F004 or F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.	(T)
   F003	The following spent nonhalogenated solvents: xylene, acetone, ethyl acetate, ethyl benzene, ethyl ether, methyl isobutyl ketone, n-butyl alcohol, cyclohexanone, and methanol; all spent solvent mixtures/blends containing, before use, only the above spent nonhalogenated solvents; and all spent solvent mixtures/blends containing, before use, one or more of the above nonhalogenated solvents, and a total of 10 percent or more (by volume) of one or more of those solvents listed in F001, F002, F004 and F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.	(I)*
   F004	The following spent nonhalogenated solvents: cresols and cresylic acid, and nitrobenzene; all spent solvent mixtures/blends containing, before use, a total of 10 percent or more (by volume) of one or more of the above nonhalogenated solvents or those solvents listed in F001, F002 and F005; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.	(T)
   F005	The following spent nonhalogenated solvents: toluene, methyl ethyl ketone, carbon disulfide, isobutanol, and pyridine, benzene, 2-ethoxyethanol, and 2-nitropropane; all spent solvent mixtures/blends containing, before use, a total of 10 percent or more (by volume) of one or more of the above nonhalogenated solvents or those solvents listed in F001, F002 or F004; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.	(I,T)
   F006	Wastewater treatment sludges from electroplating operations, except from the following processes: (1) sulfuric acid anodizing of aluminum; (2) tin plating on carbon steel; (3) zinc plating (segregated basis) on carbon steel; (4) aluminum or zinc-aluminum plating on carbon steel; (5) cleaning/stripping associated with tin, zinc and aluminum plating on carbon steel; and (6) chemical etching and milling of aluminum.	(T)
   F007	Spent cyanide plating bath solutions from electroplating operations.	(R,T)
   F008	Plating bath residues from the bottom of plating baths from electroplating operations where cyanides are used in the process.	(R,T)
   F009	Spent stripping and cleaning bath solutions from electroplating operations where cyanides are used in the process.	(R,T)
   F010	Quenching bath residues from oil baths from metal heat treating operations where cyanides are used in the process.	(R,T)
   F011	Spent cyanide solutions from salt bath pot cleaning from metal heat treating operations.	(R,T)
   F012	Quenching wastewater treatment sludges from metal heat treating operations where cyanides are used in the process.	(T)
   F019	Wastewater treatment sludges from the chemical conversion coating of aluminum except from zirconium phosphating in aluminum can washing when such phosphating is an exclusive conversion coating process. Wastewater treatment sludges from the manufacturing of motor vehicles using a zinc phosphating process will not be subject to this listing at the point of generation if the wastes are not placed on the land prior to shipment to a landfill for disposal and are either: disposed in a municipal or industrial landfill unit that is equipped with at least a single clay liner and is permitted, licensed or otherwise authorized by the state; or disposed in a landfill unit subject to, or otherwise meeting, the landfill requirements in Parts 360 and 363 of this Title and sections 373-2.15(c) and 373-3.14(j) of this Title. For the purposes of this listing, motor vehicle manufacturing is defined in clause (2)(iv)(a) of this subdivision, clause (2)(iv)(b) of this subdivision describes the recordkeeping requirements for motor vehicle manufacturing facilities.	(T)
   F020	Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production or manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of tri- or tetrachlorophenol, or of intermediates used to produce their pesticide derivatives. (This listing does not include wastes from the production of hexachlorophene from highly purified 2,4,5-trichlorophenol.)	(H)
   F02I	Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production or manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of pentachlorophenol, or of intermediates used to produce its derivatives.	(H)
   F022	Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of tetra-, penta-, or hexachlorobenzenes under alkaline conditions.	(H)
   F023	Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production of materials on equipment previously used for the production or manufacturing use (as a reactant, chemical intermediate, component in a formulating process) of tri- and tetra-chlorophenols. (This listing does not include wastes from equipment used only for the production or use of hexachlorophene from highly purified 2,4,5-trichlorophenol.)	(H)
   F024	Process wastes, including but not limited to, distillation residues, heavy ends, tars, and reactor clean-out wastes, from the production of certain chlorinated aliphatic hydrocarbons by free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon chain lengths ranging from one to and including five, with varying amounts and positions of chlorine substitution. (This listing does not include wastewaters, wastewater treatment sludges, spent catalysts, and wastes listed in subdivision [b] or [c] of this section.)	(T)
   F025	Condensed light ends, spent filters and filter aids, and spent desiccant wastes from the production of certain chlorinated aliphatic hydrocarbons, by free radical catalyzed processes. These chlorinated aliphatic hydrocarbons are those having carbon chain lengths ranging from one to and including five, with varying amounts and positions of chlorine substitution.	(T)
   F026	Wastes (except wastewater and spent carbon from hydrogen chloride purification) from the production of materials on equipment previously used for the manufacturing use (as a reactant, chemical intermediate, or component in a formulating process) of tetra-, penta-, or hexachlorobenzene under alkaline conditions.	(H)
   F027	Discarded unused formulations containing tri-, tetra-, or pentachlorophenol or discarded unused formulation containing compounds derived from these chlorophenols. (This listing does not include formulations containing hexachlorophene synthesized from prepurified 2,4,5-trichlorophenol as the sole component.)	(H)
   F028	Residues resulting from the incineration or thermal treatment of soil contaminated with EPA hazardous waste numbers F020, F021, F022, F023, F026 and F027.	(T)
   F032	Wastewaters (except those that have not come into contact with process contaminants), process residuals, preservative drippage, and spent formulations from wood preserving processes generated at plants that currently use or have previously used chlorophenolic formulations (except potentially cross-contaminated wastes that have had the F032 waste code deleted in accordance with subdivision [f] of this section or potentially cross-contaminated wastes that are otherwise currently regulated as hazardous wastes [i.e., F034 or F035], and where the generator does not resume or initiate use of chlorophenolic formulations). This listing does not include K001 bottom sediment sludge from the treatment of wastewater from wood preserving processes that use creosote and/or pentachlorophenol.	(T)
   F034	Wastewaters (except those that have not come into contact with process contaminants), process residuals, preservative drippage, and spent formulations from wood preserving processes generated at plants that use creosote formulations. This listing does not include K001 bottom sediment sludge from the treatment of wastewater from wood preserving processes that use creosote and/or pentachlorophenol.	(T)
   F035	Wastewaters (except those that have not come into contact with process contaminants), process residuals, preservative drippage, and spent formulations from wood preserving processes generated at plants that use inorganic preservatives containing arsenic or chromium. This listing does not include K001 bottom sediment sludge from the treatment of wastewater frorn wood preserving processes that use creosote and/or pentachlorophenol.	(T)
   F037	Petroleum refinery primary oil/water/solids separation sludge; any sludge generated from the gravitational separation of oil/ water/solids during the storage or treatment of process wastewaters and oily cooling wastewaters from petroleum refineries. Such sludges include, but are not limited to, those generated in: oil/water/solids separators; tanks and impoundments; ditches and other conveyances; sumps; and stormwater units receiving dry weather flow. Sludge generated in stormwater units that do not receive dry weather flow, sludges generated from non-contact once-through cooling waters segregated for treatment from other process or oily cooling waters, sludges generated in aggressive biological treatment units as defined in subparagraph (2)(ii) of this subdivision (including sludges generated in one or more additional units after wastewaters have been treated in aggressive biological treatment units) and K051 wastes are not included in this listing. This listing does include residuals generated from processing or recycling oil-bearing hazardous secondary materials excluded under section 371.1(e)(1)(xii)(a) of this Part, if those residuals are to be disposed of.	(T)
   F038	Petroleum refinery secondary (emulsified) oil/water/solids separation sludge; any sludge and/or float generated from the physical and/or chemical separation of oil/water/solids in process wastewaters and oily cooling wastewaters from petroleum refineries. Such wastes include, but are not limited to, all sludges and floats generated in: induced air flotation (IAF) units, tanks and impoundments, and all sludges generated in DAF units. Sludges generated in stormwater units that do not receive dry weather flow, sludges generated from non-contact once-through cooling waters segregated for treatment from other process or oily cooling waters, sludges and floats generated in aggressive biological treatment units as defined in subparagraph (2)(ii) of this subdivision (including sludges and floats generated in one or more additional units after wastewaters have been treated in aggressive biological treatment units) and F037, K048, and K051 wastes are not included in this listing.	(T)
   F039	Leachate (liquids that have percolated through land disposed wastes) resulting from the disposal of more than one restricted waste classified as hazardous under this section. (Leachate resulting from the disposal of one or more of the following EPA hazardous wastes and no other hazardous waste retains its EPA hazardous waste number(s): F020, F021, F022, F026, F027, and/or F028.)	(T)

   * (I,T) should be used to specify mixtures that are ignitable and contain toxic constituents.

6. (2) Listing specific definitions:

   1. (i) For the purposes of the F037 and F038 listings, oil/water/solids is defined as oil and/or water and/or solids.

      1. (a) For the purposes of the F037 and F038 listings, aggressive biological treatment units are defined as units which employ one of the following four treatment methods: activated sludge; trickling filter; rotating biological contactor for the continuous accelerated biological oxidation of wastewaters; or high-rate aeration. High-rate aeration is a system of surface impoundments or tanks, in which intense mechanical aeration is used to completely mix the wastes, enhance biological activity, and:

         1. (1) the units employ a minimum of six hp per million gallons of treatment volume; and
         2. (2) either the hydraulic retention time of the unit is no longer than five days; or
         3. (3) the hydraulic retention time is no longer than 30 days and the unit does not generate a sludge that is a hazardous waste by the toxicity characteristic.

      2. (b) Generators and treatment, storage and disposal facilities have the burden of proving that their sludges are exempt from listing as F037 and F038 wastes under this definition. Generators and treatment, storage and disposal facilities must maintain, in their operating or other onsite records, documents and data sufficient to prove that:

         1. (1) the unit is an aggressive biological treatment unit as defined in this subparagraph; and

         2. (2) the sludges sought to be exempted from the definitions of F037 and/or F038 were actually generated in the aggressive biological treatment unit.

            (iii)

      3. (a) For the purposes of the F037 listing, sludges are considered to be generated at the moment of deposition in the unit, where deposition is defined as at least a temporary cessation of lateral particle movement.

      4. (b) For the purposes of the F038 listing:

         1. (1) sludges are considered to be generated at the moment of deposition in the unit, where deposition is defined as at least a temporary cessation of lateral particle movement; and
         2. (2) floats are considered to be generated at the moment they are formed in the top of the unit.

      (ii)

   2. (iv) For the purposes of the F019 listing, the following apply to wastewater treatment sludges from the manufacturing of motor vehicles using a zinc phosphating process.

      1. (a) Motor vehicle manufacturing is defined to include the manufacture of automobiles and light trucks/utility vehicles (including light duty vans, pick-up trucks, minivans, and sport utility vehicles). Facilities must be engaged in manufacturing complete vehicles (body and chassis or unibody) or chassis only.
      2. (b) Generators must maintain in their on-site records documentation and information sufficient to prove that the wastewater treatment sludges to be exempted from the F019 listing meet the conditions of the listing. These records must include: the volume of waste generated and disposed of offsite; documentation showing when the waste volumes were generated and sent offsite; the name and address of the receiving facility; and documentation confirming receipt of the waste by the receiving facility. Generators must maintain these records on-site for no less than three years. The retention period for the records is automatically extended during the course of any enforcement action or as requested by the department.

7. (c) Hazardous wastes from specific sources. (1) The following solid wastes are listed hazardous waste from specific sources unless excluded under section 370.3(a) and (c) of this Title and listed in Appendix 24, infra:

   1. (2) Listing specific definitions:

      1. (i) For purposes of the K181 listing, dyes and/or pigments production is defined to include manufacture of the following product classes: dyes, pigments, or FDA certified colors that are classified as azo, triarylmethane, perylene or anthraquinone classes. Azo products include azo, monoazo, diazo, triazo, polyazo, azoic, benzidine, and pyrazolone products. Triarylmethane products include both triarylmethane and triaphenylmethane products. Wastes that are not generated at a dyes and/or pigments manufacturing site, such as wastes from the offsite use, formulation, and packaging of dyes and/or pigments, are not included in the K181 listing.

   2. (3) K181 listing levels. Nonwastewaters containing constituents in amounts equal to or exceeding the following levels during any calendar year are subject to the K181 listing, unless the conditions in the K181 listing are met.

      Constituent	Chemical abstracts No.	Mass levels (kg/yr)
      Aniline	62-53-3	9,300
      o-Anisidine	90-04-0	110
      4-Chloroaniline	106-47-8	4,800
      p-Cresidine	120-71-8	660
      2,4-Dimethylaniline	95-68-1	100
      1,2-Phenylenediamine	95-54-5	710
      1,3-Phenylenediamine	108-45-2	1,200

   3. (4) Procedures for demonstrating that dyes and/or pigment nonwastewaters are not K181. The procedures described in subparagraphs (4)(i) through (4)(iii) and (4)(v) of this subdivision establish when nonwastewaters from the production of dyes/pigments would not be hazardous (these procedures apply to wastes that are not disposed in landfill units or treated in combustion units as specified in paragraph (1) of this subdivision). If the nonwastewaters are disposed in landfill units or treated in combustion units as described in paragraph (1) of this subdivision, then the nonwastewaters are not hazardous. In order to demonstrate that it is meeting the landfill disposal or combustion conditions contained in the K181 listing description, the generator must maintain documentation as described in subparagraph (4)(iv) of this subdivision.

      1. (i) Determination based on no K181 constituents. Generators that have knowledge (e.g., knowledge of constituents in wastes based on prior sampling and analysis data and/or information about raw materials used, production processes used, and reaction and degradation products formed) that their wastes contain none of the K181 constituents (see paragraph [3] of this subdivision) can use their knowledge to determine that their waste is not K181. The generator must document the basis for all such determinations on an annual basis and keep each annual documentation for three years.

      2. (ii) Determination for generated quantities of 1,000 MT/yr or less for wastes that contain K181 constituents. If the total annual quantity of dyes and/or pigment nonwastewaters generated is 1,000 metric tons or less, the generator can use knowledge of the wastes (e.g., knowledge of constituents in wastes based on prior analytical data and/or information about raw materials used, production processes used, and reaction and degradation products formed) to conclude that annual mass loadings for the K181 constituents are below the listing levels of paragraph (3) of this subdivision. To make this determination, the generator must:

         1. (a) Each year document the basis for determining that the annual quantity of nonwastewaters expected to be generated will be less than 1,000 metric tons.
         2. (b) Track the actual quantity of nonwastewaters generated from January 1 through December 31 of each year. If, at any time within the year, the actual waste quantity exceeds 1,000 metric tons, the generator must comply with the requirements of subparagraph (4)(iii) of this subdivision for the remainder of the year.
         3. (c) Keep a running total of the K181 constituent mass loadings over the course of the calendar year.

         4. (d) Keep the following records on site for the three most recent calendar years in which the hazardous waste determinations are made:

            1. (1) The quantity of dyes and/or pigment nonwastewaters generated.
            2. (2) The relevant process information used.
            3. (3) The calculations performed to determine annual total mass loadings for each K181 constituent in the nonwastewaters during the year.

      3. (iii) Determination for generated quantities greater than 1,000 MT/yr for wastes that contain K181 constituents. If the total annual quantity of dyes and/or pigment nonwastewaters generated is greater than 1,000 metric tons, the generator must perform all of the steps described in clauses ([athrough [k) of this subparagraph) in order to make a determination that its waste is not K181.

         1. (a) Determine which K181 constituents (see paragraph [3] of this subdivision) are reasonably expected to be present in the wastes based on knowledge of the wastes (e.g., based on prior sampling and analysis data and/or information about raw materials used, production processes used, and reaction and degradation products formed).
         2. (b) If 1,2-phenylenediamine is present in the wastes, the generator can use either knowledge or sampling and analysis procedures to determine the level of this constituent in the wastes. For determinations based on use of knowledge, the generator must comply with the procedures for using knowledge described in subparagraph (ii) of this paragraph and keep the records described in clause (ii)(d) of this paragraph. For determinations based on sampling and analysis, the generator must comply with the sampling and analysis and recordkeeping requirements described below in this subdivision.

         3. (c) Develop a waste sampling and analysis plan (or modify an existing plan) to collect and analyze representative waste samples for K181 constituents reasonably expected to be present in the wastes. At a minimum, the plan must include:

            1. (1) a discussion of the number of samples needed to characterize the wastes fully;
            2. (2) the planned sample collection method to obtain representative waste samples;
            3. (3) a discussion of how the sampling plan accounts for potential temporal and spatial variability of the wastes;
            4. (4) a detailed description of the test methods to be used, including sample preparation, clean up (if necessary), and determinative methods.

         4. (d) Collect and analyze samples in accordance with the waste sampling and analysis plan.

            1. (1) The sampling and analysis must be unbiased, precise, and representative of the wastes.
            2. (2) The analytical measurements must be sufficiently sensitive, accurate and precise to support any claim that the constituent mass loadings are below the listing levels of paragraph (3) of this subdivision.
         5. (e) Record the analytical results.
         6. (f) Record the waste quantity represented by the sampling and analysis results.
         7. (g) Calculate constituent-specific mass loadings (product of concentrations and waste quantity).
         8. (h) Keep a running total of the K181 constituent mass loadings over the course of the calendar year.
         9. (i) Determine whether the mass of any of the K181 constituents listed in paragraph (3) of this subdivision generated between January 1 and December 31 of any year is below the K181 listing levels.

         10. (j) Keep the following records on site for the three most recent calendar years in which the hazardous waste determinations are made:

             1. (1) The sampling and analysis plan.The calculations performed to determine annual mass loadings.
             2. (2) The sampling and analysis results (including QA/QC data).
             3. (3) The quantity of dyes and/or pigment nonwastewaters generated.
             4. (4) The calculations performed to determine annual mass loadings.

         11. (k) Nonhazardous waste determinations must be conducted annually to verify that the wastes remain nonhazardous.

             1. (1) The annual testing requirements are suspended after three consecutive successful annual demonstrations that the wastes are nonhazardous. The generator can then use knowledge of the wastes to support subsequent annual determinations.
             2. (2) The annual testing requirements are reinstated if the manufacturing or waste treatment processes generating the wastes are significantly altered, resulting in an increase of the potential for the wastes to exceed the listing levels.
             3. (3) If the annual testing requirements are suspended, the generator must keep records of the process knowledge information used to support a nonhazardous determination. If testing is reinstated, a description of the process change must be retained.
      4. (iv) Recordkeeping for the landfill disposal and combustion exemptions. For the purposes of meeting the landfill disposal and combustion condition set out in the K181 listing description, the generator must maintain on site for three years documentation demonstrating that each shipment of waste was received by a landfill unit that is subject to or meets the landfill design standards set out in the listing description, or was treated in combustion units as specified in the listing description.
      5. (v) Waste holding and handling. During the interim period, from the point of generation to completion of the hazardous waste determination, the generator is responsible for storing the wastes appropriately. If the wastes are determined to be hazardous and the generator has not complied with the requirements of Parts 370 through 374-4 and Part 376 of this Title during the interim period, the generator is in violation and could be subject to an enforcement action for improper management.

   Industry and
   EPA hazardous		Hazard
   waste number	Hazardous waste	code
   Wood preservation:
   K001	Bottom sediment sludge from the treatment of wastewaters from wood preserving processes that use creosote and/or pentachlorophenol.	(T)
   Inorganic pigments:
   K002	Wastewater treatment sludge from the production of chrome yellow and orange pigments.	(T)
   K003	Wastewater treatment sludge from the production of molybdate orange pigments.	(T)
   K004	Wastewater treatment sludge from the production of zinc yellow pigments.	(T)
   K005	Wastewater treatment sludge from the production of chrome green pigments.	(T)
   K006	Wastewater treatment sludge from the production of chrome oxide green pigments (anhydrous and hydrated).	(T)
   K007	Wastewater treatment sludge from the production of iron blue pigments.	(T)
   K008	Oven residue from the production of chrome oxide green pigments.	(T)
   Organic chemicals:
   K009	Distillation bottoms from the production of acetaldehyde from ethylene.	(T)
   K010	Distillation side cuts from the production of acetaldehyde from ethylene.	(T)
   K011	Bottom stream from the wastewater stripper in the production of acrylonitrile.	(R,T)
   K013	Bottom stream from the acetonitrile column in the production of acrylonitrile.	(R,T)
   K014	Bottoms from the acetonitrile purification column in the production of acrylonitrile.	(T)
   K015	Still bottoms from the distillation of benzyl chloride.	(T)
   K016	Heavy ends or distillation residues from the production of carbon tetrachloride.	(T)
   K017	Heavy ends (still bottoms) from the purification column in the production of epichlorohydrin.	(T)
   K018	Heavy ends from the fractionation column in ethyl chloride production.	(T)
   K019	Heavy ends from the distillation of ethylene dichloride in ethylene dichloride production.	(T)
   K020	Heavy ends from the distillation of vinyl chloride monomer production.	(T)
   K021	Aqueous spent antimony catalyst waste from fluoromethanes production.	(T)
   K022	Distillation bottom tars from the production of phenol/acetone from cumene.	(T)
   K023	Distillation light ends from the production of phthalic anhydride from naphthalene.	(T)
   K024	Distillation bottoms from the production of phthalic anhydride from naphthalene.	(T)
   K025	Distillation bottoms from the production of nitrobenzene by the nitration of benzene.	(T)
   K026	Stripping still tails from the production of methyl ethyl pyridines.	(T)
   K027	Centrifuge and distillation residues from toluene diisocyanate production.	(R,T)
   K028	Spent catalyst from the hydrochlorinator reactor in the production of 1,1,1-trichloethane.	(T)
   K029	Waste from the product steam stripper in the production of 1,1,1-trichloroethane.	(T)
   K030	Column bottoms or heavy ends from the combined production of trichloroethylene and perchloroethylene.	(T)
   K083	Distillation bottoms from aniline production.	(T)
   K085	Distillation or fractionation column bottoms from the production of chlorobenzenes.	(T)
   K093	Distillation light ends from the production of phthalic anhydride from ortho-xylene.	(T)
   K094	Distillation bottoms from the production of phthalic anhydride from ortho-xylene.	(T)
   K095	Distillation bottoms from the production of 1,1,1-trichloroethane.	(T)
   K096	Heavy ends from the heavy ends column from the production of 1,1,1-trichloroethane.	(T)
   K103	Process residues from aniline extraction from the production of aniline.	(T)
   K104	Combined wastewater streams generated from nitrobenzene/aniline production.	(T)
   K105	Separated aqueous stream from the reactor product washing step in the production of chlorobenzene.	(T)
   K107	Column bottoms from product separation from the production of 1,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides.	(C,T)
   K108	Condensed column overheads from product separation and condensed reactor vent gases from the production of 1,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides.	(I,T)
   K109	Spent filter cartridges from product purification from the production of 1,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides.	(T)
   K110	Condensed column overheads from intermediate separation from the production of 1,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides.	(T)
   K111	Product washwaters from the production of dinitrotoluene via nitration of toluene.	(C,T)
   K112	Reaction by-product water from the drying column in the production of toluenediamine via hydrogenation of dinitrotoluene.	(T)
   K113	Condensed liquid light ends from the purification of toluenediamine in the production of toluenediamine via hydrogenation of dinitrotoluene.	(T)
   K114	Vicinals from the purification of toluenediamine in the production of toluenediamine via hydrogenation of dinitrotoluene.	(T)
   K115	Heavy ends from the purification of toluenediamine in the production of toluenediamine via hydrogenation of dinitrotoluene.	(T)
   K116	Organic condensate from the solvent recovery column in the production of toluene diisocyanate via phosgenation of toluenediamine.	(T)
   K117	Wastewater from the reactor vent gas scrubber in the production of ethylene dibromide via bromination of ethene.	(T)
   K118	Spent adsorbent solids from purification of ethylene dibromide in the production of ethylene dibromide via bromination of ethene.	(T)
   K136	Still bottoms from the purification of ethylene dibromide in the production of ethylene dibromide via bromination of ethene.	(T)
   K149	Distillation bottoms from the production of alpha- (or methyl-) chlorinated toluenes, ring-chlorinated toluenes, benzoyl chlorides, and compounds with mixtures of these functional groups. (This waste does not include still bottoms from the distillation of benzyl chloride.)	(T)
   K150	Organic residuals, excluding spent carbon adsorbent, from the spent chlorine gas and hydrochloric acid recovery processes associated with the production of alpha- (or methyl-) chlorinated toluenes, ring-chlorinated toluenes, benzoyl chlorides, and compounds with mixtures of these functional groups.	(T)
   K151	Wastewater treatment sludges, excluding neutralization and biological sludges, generated during the treatment of wastewaters from the production of alpha- (or methyl-) chlorinated toluenes, ring-chlorinated toluenes, benzoyl chlorides, and compounds with mixtures of these functional groups.	(T)
   K156	Organic waste (including heavy ends, still bottoms, light ends, spent solvents, filtrates, and decantates) from the production of carbamates and carbamoyl oximes. (This listing does not apply to wastes generated from the manufacture of 3-iodo-2-propynyl n-butylcarbamate.)	(T)
   K157	Wastewaters (including scrubber waters, condenser waters, washwaters, and separation waters) from the production of carbamates and carbamoyl oximes. (This listing does not apply to wastes generated from the manufacture of 3-iodo-2-propynyl n-butylcarbamate.)	(T)
   K158	Bag house dusts and filter/separation solids form the production of carbamates and arbamoyl oximes. (This listing does not apply to wastes generated from the manufacture of 3-iodo-2-propynyl n-butylcarbamate.)	(T)
   K159	Organics from the treatment of thiocarbamate wastes.	(T)
   K161	Purification solids (including filtration, evaporation, and centrifugation solids), bag house dust and floor sweepings from the production of dithiocarbamate acids and their salts. (This listing does not include K125 and K126.)	(R,T)
   K174	Wastewater treatment sludges from the production of ethylene dicloride or vinyl chloride monomer (including sludges that result from commingled ethylene dichloride or vinyl chloride monomer wastewater and other wastewater), unless the sludges meet the following conditions: (i) they are disposed of in a subtitle C or non-hazardous landfill licensed or permitted by the State or Federal government; (ii) they are not otherwise placed on the land prior to final disposal; and (iii) the generator maintains documentation demonstrating that the waste was either disposed of in an on-site landfill or consigned to a transporter or disposal facility that provided a written commitment to dispose of the waste in an off-site landfill. Respondents in any action brought to enforce the requirements of subtitle C must, upon a showing by the government that the respondent managed wastewater treatment sludges from the production of vinyl chloride monomer or ethylene dichloride, demonstrate that they meet the terms of the exclusion set forth above. In doing so, they must provide appropriate documentation (e.g., contracts between the generator and the landfill owner/operator, invoices documenting delivery of waste to landfill, etc.) that the terms of the exclusion were met.	(T)
   K175	Wastewater treatment sludges from the production of vinyl chloride monomer using mercuric chloride catalyst in an acetylene-based process.	(T)
   K181	Nonwastewaters from the production of dyes and/or pigments (including nonwastewaters commingled at the point of generation with nonwastewaters from other processes) that, at the point of generation, contain mass loadings of any of the constituents identified in paragraph (3) of this subdivision, that are equal to or greater than the corresponding paragraph (3) levels, as determined on a calendar year basis. These wastes will not be hazardous if the nonwastewaters are: (i) disposed in a landfill permitted under Part 360 of this Title or if out of state disposed in a 40 CFR subtitle D landfill unit subject to the design criteria in 40 CFR 258.40, as incorporated by reference in section 370.1(e) of this Title; (ii) disposed in a Part 373 landfill unit subject to either sections 373-2.14 or 373-3.14(j) of this Title or if out of state disposed in a 40 CFR subtitle C landfill unit subject to either 40 CFR 264.301 or 40 CFR 265.301, as incorporated by reference in section 370.1(e) of this Title; (iii) if out of state, disposed in other 40 CFR subtitle D landfill units that meet the design criteria in 40 CFR 258.40, 264.301, or 265.301 as incorporated by reference in section 370.1(e) of this Title; or (iv) treated in a combustion unit that is permitted under Part 373 or 40 CFR subtitle C, as incorporated by reference in section 370.1(e) of this Title, or an on-site combustion unit that is permitted under the Clean Air Act at 40 CFR parts 60, 61, or 63, as incorporated by reference by section 200.10 of this Title. For the purposes of this listing, dyes and/or pigments production is defined in subparagraph (2)(i) of this subdivision. Paragraph (4) of this subdivision describes the process for demonstrating that a facility’s nonwastewaters are not K181. This listing does not apply to wastes that are otherwise identified as hazardous under section 371.3(b),(c), (d) and (e) of this Part and subdivisions (b), (c) and (d) of this section, at the point of generation. Also, the listing does not apply to wastes generated before any annual mass loading limit is met.	(T)
   Inorganic chemicals:
   K071	Brine purification muds from the mercury cell process in chlorine production, where separately prepurified brine is not used.	(T)
   K073	Chlorinated hydrocarbon waste from the steps of the diaphragm cell process using graphite anodes in chlorine production.	(T)
   K106	Wastewater treatment sludges from the mercury cell process in chlorine production.	(T)
   Pesticides:
   K031	By-product salts generated in the production of MSMA and cacodylic acid.	(T)
   K032	Wastewater treatment sludge from the production of chlordane.	(T)
   K033	Wastewater and scrub water from the chlorination of cyclopentadiene in the production of chlordane.	(T)
   K034	Filter solids from the filtration of hexachloro-cyclopentadiene in the production of chlordane.	(T)
   K035	Wastewater treatment sludges generated in the production of creosote.	(T)
   K036	Still bottoms from toluene reclamation distillation in the production of disulfoton.	(T)
   K037	Wastewater treatment sludges from the production of disulfoton.	(T)
   K038	Wastewater from the washing and stripping of phorate production.	(T)
   K039	Filter cake from the filtration of diethylphos-phorodithioic acid in the production of phorate.	(T)
   K040	Wastewater treatment sludge from the production of phorate.	(T)
   K041	Wastewater treatment sludge from the production of toxaphene.	(T)
   K042	Heavy ends or distillation residues from the distillation of tetrachlorobenzene in the production 2,4,5-T.	(T)
   K043	2,6-Dichlorophenol waste from the production of 2,4-D.	(T)
   K097	Vacuum stripper discharge from the chlordane chlorinator in the production of chlordane.	(T)
   K098	Untreated process wastewater from the production of toxaphene.	(T)
   K099	Untreated wastewater from the production of 2,4-D.	(T)
   K123	Process wastewater (including supernates, filtrates, and washwaters) from the production of ethylenebisdithiocarbamic acid and its salts.	(T)
   K124	Reactor vent scrubber water from the production of ethylenebisdithiocarbamic acid and its salts.	(C,T)
   K125	Filtration, evaporation, and centrifugation solids from the production of ethylenebisdithiocarbamic acid and its salts.	(T)
   K126	Baghouse dust and floor sweepings in milling and packaging operations from the production or formulation of ethylenebisdithiocarbamic acid and its salts.	(T)
   K131	Wastewater from the reactor and spent sulfuric acid from the acid dryer from the production of methyl bromide.	(C,T)
   K132	Spent absorbent and wastewater separator solids from the production of methyl bromide.	(T)
   K176	Baghouse filters from the production of antimony oxide, including filters from the production of intermediates (e.g., antimony metal or crude antimony oxide).	(E)
   K177	Slag from the production of antimony oxide that is speculatively accumulated or disposed, including slag from the production of intermediates (e.g., antimony metal or crude antimony oxide).	(T)
   K178	Residues from manufacturing and manufacturing-site storage of ferric chloride from acids formed during the production of titanium dioxide using the chloride-ilmenite process.	(T)
   Explosives:
   K044	Wastewater treatment sludges from the manufacturing and processing of explosives.	(R)
   K045	Spent carbon from the treatment of wastewater containing explosives.	(R)
   K046	Wastewater treatment sludges from the manufacturing, formulation and loading of lead-based initiating compounds.	(T)
   K047	Pink/red water from TNT operations.	(R)
   Petroleum refining:
   K048	Dissolved air flotation (DAF) float from the petroleum refining industry.	(T)
   K049	Slop oil emulsion solids from the petroleum refining industry.	(T)
   K050	Heat exchanger bundle cleaning sludge from the petroleum refining industry.	(T)
   K051	API separator sludge from the petroleum refining industry.	(T)
   K052	Tank bottoms (leaded) from the petroleum refining industry.	(T)
   K169	Crude oil storage tank sediment from petroleum refining operations.	(T)
   K170	Clarified slurry oil tank sediment and/or in-line filter/separation solids from petroleum refining operation.	(T)
   K171	Spent hydrotreating catalyst from petroleum refining operations, including guard beds used to desulfurize feeds to other catalytic reactors (this listing does not include inert support media).	(I, T)
   K172	Spent hydrorefining catalyst from petroleum refining operations, including guard beds used to desulfurize feeds to other catalytic reactors (this listing does not include inert support media).	(I, T)
   Iron and steel:
   K061	Emission control dust/sludge from the primary production of steel in electric furnaces.	(T)
   K062	Spent pickle liquor generated by steel finishing operations of facilities within the iron and steel industry (SIC codes 331 and 332).	(C,T)
   Primary aluminum:
   K088	Spent potliners from primary aluminum reduction.	(T)
   Secondary lead:
   K069	Emission control dust/sludge from secondary lead smelting, except sludge generated from secondary acid scrubber systems.	(T)
   K100	Waste leaching solution from acid leaching of emission control dust/sludge from secondary lead smelting.	(T)
   Veterinary pharmaceuticals:
   K084	Wastewater treatment sludges generated during the production of veterinary pharmaceuticals from arsenic or organo-arsenic compounds.	(T)
   K101	Distillation tar residues from the distillation of aniline-based compounds in the production of veterinary pharmaceuticals from arsenic or organo-arsenic compounds.	(T)
   K102	Residue from the use of activated carbon for decolorization in the production of veterinary pharmaceuticals from arsenic or organo-arsenic compounds.	(T)
   Ink formation:
   K086	Solvent washes and sludges, caustic washes and sludges, or water washes and sludges from cleaning tubs and equipment used in the formulation of ink from pigments, driers, soaps, and stabilizers containing chromium and lead.	(T)
   Coking:
   K060	Ammonia still lime sludge from coking operations.	(T)
   K087	Decanter tank tar sludge from coking operations.	(T)
   K141	Process residues from the recovery of coal tar, including, but not limited to, collecting sump residues from the production of coke from coal or the recovery of coke by-products produced from coal. This listing does not include K087 (decanter tank tar sludges from coking operations).	(T)
   K142	Tar storage tank residues from the production of coke from coal or from the recovery of coke by-products produced from coal.	(T)
   K143	Process residues from the recovery of light oil, including, but not limited to, those generated in stills, decanters, and wash oil recovery units from the recovery of coke by-products produced from coal.	(T)
   K144	Wastewater sump residues from light oil refining, including, but not limited to, intercepting or contamination sump sludges from the recovery of coke by-products produced from coal.	(T)
   K145	Residues from naphthalene collection and recovery operations from the recovery of coke by-products produced from coal.	(T)
   K147	Tar storage tank residues from coal tar refining.	(T)
   K148	Residues from coal tar distillation, including but not limited to, still bottoms.	(T)

8. (d) Discarded commercial chemical products, off-specification species, container residues, and spill residues thereof. The following materials or items are hazardous wastes if and when they are discarded or intended to be discarded as described in section 371.1(c)(2)(i) of this Part, when they are mixed with waste oil or used oil or other material and applied to the land for dust suppression or road treatment, when they are otherwise applied to the land in lieu of their original intended use or when they are contained in products that are applied to the land in lieu of their original intended use, or when, in lieu of their original intended use, they are produced for use as (or as a component of) a fuel, distributed for use as a fuel, or burned as a fuel:

   1. (1) any commercial chemical product, or manufacturing chemical intermediate having the generic name listed in paragraph (5) or (6) of this subdivision;
   2. (2) any off-specification commercial chemical product or manufacturing chemical intermediate which, if it met specifications, would have the generic name listed in paragraph (5) or (6) of this subdivision;

   3. (3) any residue remaining in a container or inner liner removed from a container that has been used to hold any commercial chemical product or manufacturing chemical intermediate having the generic names listed in paragraph (5) or (6) of this subdivision, or any residue remaining in a container or inner liner removed from a container that has been used to hold any off-specification chemical product or manufacturing chemical intermediate, which if it met specifications, would have the generic name listed in paragraph (5) or (6) of this subdivision, unless the container is empty as defined in section 371.1(h)(2) of this Part. Note:

      Note:

      Unless the residue is being beneficially used or reused, or legitimately recycled or reclaimed, or being accumulated, stored, transported or treated prior to such use, reuse, recycling or reclamation, EPA and the department consider the residue to be intended for discard, and thus, a hazardous waste. An example of a legitimate reuse of the residue would be where the residue remains in the container and the container is used to hold the same commercial chemical product or manufacturing chemical intermediate it previously held. An example of the discard of the residue would be where the drum is sent to a drum reconditioner who reconditions the drum but discards the residues. All waste resulting from the rinsing or cleansing of the container or inner liner, by a nonaqueous solvent, is a hazardous waste. All waste resulting from the aqueous rinsing or cleansing of the container or inner liner is a hazardous waste unless exempt pursuant to section 371.1(d)(1)(ii)(d)(4).

   4. (4) any residue or contaminated soil, water or other debris resulting from the cleanup of a spill into or on any land or water of any commercial chemical product or manufacturing chemical intermediate having the generic name listed in paragraph (5) or (6) of this subdivision, or any residue or contaminated soil, water or other debris resulting from the cleanup of a spill, into or on any land or water, of any off-specification chemical product or manufacturing chemical intermediate which, if it met specifications, would have the generic name listed in paragraph (5) or (6) of this subdivision. Note:

      Note:

      The phrase “commercial chemical product or manufacturing chemical intermediate having the generic name listed in. . .” refers to a chemical substance which is manufactured or formulated for commercial or manufacturing use which consists of the commercially pure grade of the chemical, any technical grades of the chemical that are produced or marketed, and all formulations in which the chemical is the sole active ingredient. It does not refer to a material, such as a manufacturing process waste, that contains any of the substances listed in paragraph (5) or (6). Where a manufacturing process waste is deemed to be a hazardous waste because it contains a substance listed in paragraph (5) or (6), such waste will be listed in either subdivision (b) or (c) of this section, or will be identified as a hazardous waste by the characteristics set forth in section 371.3 of this Part.

   5. (5) Acute hazardous waste. The commercial chemical products, manufacturing chemical intermediates or off-specification commercial chemical products or manufacturing chemical intermediates referred to in paragraphs (1) through (4) of this subdivision, are identified as acute hazardous wastes (H) and are subject to the small quantity exclusion defined in section 371.1(f)(5) of this Part. Note:

      Note:

      For the convenience of the regulated community the primary hazardous properties of the materials have been indicated by the letters T [Toxicity], and R [Reactivity]. Absence of a letter indicates that the compound only is listed for acute toxicity.

      These wastes and their corresponding EPA hazardous waste numbers are:

      EPA	Chemical	Substance
      hazardous	abstracts No.
      waste No.
      P023	107-20-0	Acetaldehyde, chloro-
      P002	591-08-2	Acetamide, N-(aminothioxomethyl)-
      P057	640-19-7	Acetamide, 2-fluoro-
      P058	62-74-8	Acetic acid, fluoro-, sodium salt
      P002	591-08-2	1-Acetyl-2-thiourea
      P003	107-02-8	Acrolein
      P070	116-06-3	Aldicarb
      P203	1646-88-4	Aldicarb sulfone
      P004	309-00-2	Aldrin
      P005	107-18-6	Allyl alcohol
      P006	20859-73-8	Aluminum phosphide (R,T)
      P007	2763-96-4	5-(Aminomethyl)-3-isoxazolol
      P008	504-24-5	4-Aminopyridine
      P009	131-74-8	Ammonium picrate (R)
      P119	7803-55-6	Ammonium vanadate
      P099	506-61-6	Argentate (1-), bis (cyano-C)-, potassium
      P010	7778-39-4	Arsenic acid H3AsO4
      P012	1327-53-3	Arsenic oxide As2 O3
      P011	1303-28-2	Arsenic oxide As2O5
      P011	1303-28-2	Arsenic pentoxide
      P012	1327-53-3	Arsenic trioxide
      P038	692-42-2	Arsine, diethyl-
      P036	696-28-6	Arsonous dichloride, phenyl-
      P054	151-56-4	Aziridine
      P067	75-55-8	Aziridine, 2-methyl-
      P013	542-62-1	Barium cyanide
      P024	106-47-8	Benzenamine, 4-chloro-
      P077	100-01-6	Benzenamine, 4-nitro-
      P028	100-44-7	Benzene, (chloromethyl)-
      P042	51-43-4	1,2-Benzenediol, 4-[1-hydroxy-2-(methylamino) ethyl]-, (R)-
      P046	122-09-8	Benzeneethanamine, alpha, alpha-dimethyl-
      P014	108-98-5	Benzenethiol
      P127	1563-66-2	7-Benzofuranol, 2,3-dihydro-2,2-dimethyl-, methylcarbamate
      P188	57-64-7	Benzoic acid, 2-hydroxy-, compd. w/(3aS-cis)-1,2,3a, 8,8a- hexahydro-1,3a,8-trimethylpyrrolo[2,3-b]indol-5-yl methycarbamate ester (1:1)
      P001	181-81-2	2H-1-Benzopyran-2-one, 4-hydroxy-3- (3-oxo-1-phenylbutyl)-1, & salts, when present at concentrations greater than 0.3 percent
      P028	100-44-7	Benzyl chloride
      P015	7440-41-7	Beryllium powder
      P017	598-31-2	Bromoacetone
      P018	357-57-3	Brucine
      P045	39196-18-4	2-Butanone, 3,3-dimethyl- 1-(methylthio)-, O-[(methylamino) carbonyl] oxime
      P021	592-01-8	Calcium cyanide
      P021	592-01-8	Calcium cyanide Ca(CN)2
      P189	55285-14-8	Carbamic acid, [(dibutylamino)-thio]methyl-, 2, 3-dihydro-2,2-dimethyl-7-benzofuranyl ester
      P191	644-64-4	Carbamic acid, dimethyl-, 1-[(dimethyl- amino)carbonyl]-5-methyl-1H-pyrazol-3-yl ester
      P192	119-38-0	Carbamic acid, dimethyl-, 3-methyl-1(1-methylethyl)-1H-pyrazol-5yl ester
      P190	1129-41-5	Carbamic acid, methyl-, 3-methylphenyl ester
      P127	1563-66-2	Carbofuran
      P022	75-15-0	Carbon disulfide
      P095	75-44-5	Carbonic dichloride
      P189	55285-14-8	Carbosulfan
      P023	107-20-0	Chloroacetaldehyde
      P024	106-47-8	p-Chloroaniline
      P026	5344-82-1	1-(o-Chlorophenyl)thiourea
      P027	542-76-7	3-Chloropropionitrile
      P029	544-92-3	Copper cyanide
      P029	544-92-3	Copper cyanide Cu(CN)
      P202	64-00-6	m-Comenyl methylcarbamate
      P030		Cyanides (soluble cyanide salts), not otherwise specified
      P031	460-19-5	Cyanogen
      P033	506-77-4	Cyanogen chloride
      P033	506-77-4	Cyanogen chloride (CN)Cl
      P034	131-89-5	2-Cyclohexyl-4, 6-dinitrophenol
      P016	542-88-1	Dichloromethyl ether
      P036	696-28-6	Dichlorophenylarsine
      P037	60-57-1	Dieldrin
      P038	692-42-2	Diethylarsine
      P041	311-45-5	Diethyl-p-nitrophenyl phosphate
      P040	297-97-2	O,O-Diethyl O-pyrazinyl phosphorothioate
      P043	55-91-4	Diisopropylfluorophosphate (DFP)
      P004	309-00-2	1,4,5,8-Dimethanonaphthalene, 1,2,3,4,10,10- hexa- chloro-1,4,4a,5,8,8a,- hexahydro-, (1alpha, 4alpha, 4abeta, 5alpha, 8alpha, 8abeta) -
      P060	465-73-6	1,4,5,8- Dimethanonaphthalene, 1,2,3,4,10, 10-hexa-chloro- 1,4,4a,5,8,8a- hexahydro-, (1alpha, 4alpha, 4abeta, 5beta, 8beta, 8abeta) -
      P037	60-57-1	2,7:3,6-Dimethanonaphth[2,3-b]oxirene 3,4,5,6,9,9- hexachloro- 1a,2,2a,3,6,6a,7,7a-octahydro-, (1-a-alpha, 2beta, 2aalpha, 3beta, 6beta, 6aalpha, 7beta, 7aalpha) -
      P051	172-20-8	2,7:3,6-Dimethanonaphth [2,3-b]oxirene, 3,4,5,6,9,9-hexachloro-1a,2,2a,3,6,6a,7,7a-octahydro-, (1aalpha, 2beta, 2abeta, 3alpha, 6alpha, 6abeta, 7beta, 7aalpha)-, & metabolites
      P044	60-51-5	Dimethoate
      P046	122-09-8	alpha,alpha-Dimethylphenethylamine
      P191	644-64-4	Dimetilan
      P047	1534-52-1	4,6-Dinitro-o-cresol, & salts
      P048	51-28-5	2,4-Dinitrophenol
      P020	88-85-7	Dinoseb
      P085	152-16-9	Diphosphoramide, octamethyl-
      P111	107-49-3	Diphosphoric acid, tetraethyl ester
      P039	298-04-4	Disulfoton
      P049	541-53-7	Dithiobiuret
      P185	26419-73-8	1,3-Dithiolane-2-carboxaldehyde, 2,4-dimethyl-,0-[(methylamino)-carbonyl]oxime
      P050	115-29-7	Endosulfan
      P088	145-73-3	Endothall
      P051	72-20-8	Endrin
      P051	72-20-8	Endrin, & metabolites
      P042	51-43-4	Epinephrine
      P031	460-19-5	Ethanedinitrile
      P194	23135-22-0	Ethanimidothioic acid, 2-(dimethylamino)-N-[[(methylamino) carbonyl]oxy]-2-oxo-, methyl ester
      P066	16752-77-5	Ethanimidothioic acid, N-[[(methylamino) carbonyl]oxy]-, methyl ester
      P101	107-12-0	Ethyl cyanide
      P054	151-56-4	Ethyleneimine
      P097	52-85-7	Famphur
      P056	7782-41-4	Fluorine
      P057	640-19-7	Fluoroacetamide
      P058	62-74-8	Fluoroacetic acid, sodium salt
      P198	23422-53-9	Formetanate hydrochloride
      P197	17702-57-7	Formparanate
      P065	628-86-4	Fulminic acid, mercury (2+) salt (R,T)
      P059	76-44-8	Heptachlor
      P062	757-58-4	Hexaethyl tetraphosphate
      P116	79-19-6	Hydrazinecarbothioamide
      P068	60-34-4	Hydrazine, methyl-
      P063	74-90-8	Hydrocyanic acid
      P063	74-90-8	Hydrogen cyanide
      P096	7803-51-2	Hydrogen phosphide
      P060	465-73-6	Isodrin
      P192	119-38-0	Isolan
      P202	64-00-6	3-Isopropylphenyl N-methylcarbamate
      P007	2763-96-4	3(2H)-Isoxazolone, 5-(aminomethyl)-
      P196	15339-3603	Manganese, bis(dimethylcarbamodithioato-S,S')-
      P196	15339-36-3	Manganese dimethyldithiocarbamate
      P092	62-38-4	Mercury, (acetato-O)phenyl-
      P065	628-86-4	Mercury fulminate (R,T)
      P198	233422-53-9	Methanimidamide, N, N-dimethyl-N'-[3-[[(methylamino)-carbonyl]oxy]phenyl]-, monohydrochloride
      P197	17702-57-7	Methanimidamide, N, N-dimethyl-N'-[2-methyl-4[(methylamino)carbonyl]oxy]phenyl]-
      P082	62-75-9	Methanamine, N-methyl-N-nitroso-
      P064	624-83-9	Methane, isocyanato-
      P016	542-88-1	Methane, oxybis[chloro-
      P112	509-14-8	Methane, tetranitro-(R)
      P118	75-70-7	Methanethiol, trichloro-
      P050	115-29-7	6,9-Methano-2,4, 3-benzodioxathiepin, 6,7,8,9,10,10- hexachloro-1,5,5a,6,9,9a-hexahydro-, 3-oxide
      P059	76-44-8	4, 7-Methano-lH-indene, 1,4,5,6,7,8,8-heptachloro- 3a,4,7,7a-tetrahydro-
      P199	2032-65-7	Methiocarb
      P066	16752-77-5	Methomyl
      P068	60-34-4	Methyl hydrazine
      P064	624-83-9	Methyl isocyanate
      P069	75-86-5	2-Methyllactonitrile
      P071	298-00-0	Methyl parathion
      P190	1129-41-5	Metolcarb
      P128	315-18-4	Mexacarbate
      P072	86-88-4	alpha-Naphthylthiourea
      P073	13463-39-3	Nickel carbonyl
      P073	13463-39-3	Nickel carbonyl Ni(CO)4, (T-4)-
      P074	557-19-7	Nickel cyanide
      P074	557-19-7	Nickel cyanide Ni(CN)2
      P075	154-11-5	Nicotine, & salts
      P076	10102-43-9	Nitric oxide
      P077	100-01-6	p-Nitroaniline
      P078	10102-44-0	Nitrogen dioxide
      P076	10102-43-9	Nitrogen oxide NO
      P078	10102-44-0	Nitrogen oxide NO2
      P081	55-63-0	Nitroglycerine (R)
      P082	62-75-9	N-Nitrosodimethylamine
      P084	4549-40-0	N-Nitrosomethylvinylamine
      P085	152-16-9	Octamethylpyrophosphoramide
      P087	20816-12-0	Osmium oxide OsO4, (T-4)-
      P087	20816-12-0	Osmium tetroxide
      P088	145-73-3	7-Oxabicyclo[2.2.l]heptane-2, 3-dicarboxylic acid
      P194	23135-22-0	Oxamyl
      P089	56-38-2	Parathion
      P034	131-89-5	Phenol, 2-cyclohexyl-4, 6-dinitro-
      P128	315-18-4	Phenol, 4-(dimethylamino)-3,5-dimethyl-,methylcarbamate (ester)
      P199	2032-65-7	Phenol,(3,5-dimethyl-4-(methylthio)-, methylcarbamate
      P202	64-00-6	Phenol,3-(1-methylethyl)-,methyl carbamate
      P201	2631-37-0	Phenol, 3-methyl-5-(1-methylethyl)-,methyl carbamate
      P048	51-28-5	Phenol, 2,4-dinitro-
      P047	1534-52-1	Phenol, 2-methyl-4,6-dinitro-, & salts
      P020	88-85-7	Phenol, 2-(1-methylpropyl)-4, 6-dinitro-
      P009	131-74-8	Phenol, 2,4,6-trinitro-, ammonium salt (R)
      P092	62-38-4	Phenylmercury acetate
      P093	103-85-5	Phenylthiourea
      P094	298-02-2	Phorate
      P095	75-44-5	Phosgene
      P096	7803-51-2	Phosphine
      P041	311-45-5	Phosphoric acid, diethyl 4-nitrophenyl ester
      P039	298-04-4	Phosphorodithioic acid O,O-diethyl S-[2-(ethylthio)ethyl] ester
      P094	298-02-2	Phosphorodithioic acid, O,O-diethyl S-[(ethylthio) methyl] ester
      P044	60-51-5	Phosphorodithioic acid, O,O-dimethyl S-[2-(methylamino) -2-oxoethyl] ester
      P043	55-91-4	Phosphorofluoridic acid, bis(1-methylethyl) ester
      P089	56-38-2	Phosphorothioic acid, O,O-diethyl O-(4-nitrophenyl) ester
      P040	297-97-2	Phosphorothioic acid, O,O-diethyl O-pyrazinyl ester
      P097	52-85-7	Phosphorothioic acid, O-[4-[(dimethylamino) sulfonyl] phenyl] O,O-dimethyl ester
      P071	298-00-0	Phosphorothioic acid, O,O,-dimethyl O-(4-nitrophenyl) ester
      P204	57-47-6	Physostigmine
      P188	57-64-7	Physostigimine salicylate
      P110	78-00-2	Plumbane, tetraethyl-
      P098	151-50-8	Potassium cyanide
      P098	151-50-8	Potassium cyanide K(CN)
      P099	506-61-6	Potassium silver cyanide
      P201	2631-37-0	Promecarb
      P070	116-06-3	Propanal, 2-methyl-2- (methylthio)-, O- [(methylamino)carbonyl]oxime
      P203	1646-88-4	Propanal, 2-methyl-2-(methyl-sulfonyl)-, 0-[(methylamino)carbonyl] oxime
      P101	107-12-0	Propanenitrile
      P027	542-76-7	Propanenitrile, 3-chloro-
      P069	75-86-5	Propanenitrile, 2-hydroxy-2-methyl-
      P081	55-63-0	1,2,3-Propanetriol, trinitrate (R)
      P017	598-31-2	2-Propanone, 1-bromo-
      P102	107-19-7	Propargyl alcohol
      P003	107-02-8	2-Propenal
      P005	107-18-6	2-Propen-1-ol
      P067	75-55-8	1,2-Propylenimine
      P102	107-19-7	2-Propyn-1-ol
      P008	504-24-5	4-Pyridinamine
      P075	154-11-5	Pyridine, 3-(1-methyl- 2-pyrrolidinyl)-, (S)-, & salts
      P204	57-47-6	Pyrrolo[2,3-b]indol-5-ol, 1,2,3,3a,8,8a-hexahydro-1,3a, 8-trimethyl-, methylcarbamate (ester), (3aS-cis)-
      P114	12039-52-0	Selenious acid, dithallium(1 +) salt
      P103	630-10-4	Selenourea
      P104	506-64-9	Silver cyanide
      P104	506-64-9	Silver cyanide Ag(CN)
      P105	26628-22-8	Sodium azide
      P106	143-33-9	Sodium cyanide
      P106	143-33-9	Sodium cyanide Na(CN)
      P108	157-24-9	Strychnidin-10-one, & salts
      P018	357-57-3	Strychnidin-10-one, 2,3-dimethoxy-
      P108	157-24-9	Strychnine, & salts
      P115	7446-18-6	Sulfuric acid, dithallium(1 +) salt
      P109	3689-24-5	Tetraethyldithio pyrophosphate
      P110	78-00-2	Tetraethyl lead
      P111	107-49-3	Tetraethyl pyrophosphate
      P112	509-14-8	Tetranitromethane (R)
      P062	757-58-4	Tetraphosphoric acid, hexaethyl ester
      P113	1314-32-5	Thallic oxide
      P113	1314-32-5	Thallium oxide Tl2O3
      P114	12039-52-0	Thallium(I) selenite
      P115	7446-18-6	Thallium(I) sulfate
      P109	3689-24-5	Thiodiphosphoric acid, tetraethyl ester
      P045	39196-18-4	Thiofanox
      P049	541-53-7	Thioimidodicarbonic diamide [(H2N)C(S)] 2NH
      P014	108-98-5	Thiophenol
      P116	79-19-6	Thiosemicarbazide
      P026	5344-82-1	Thiourea, (2-chlorophenyl)-
      P072	86-88-4	Thiourea, 1-naphthalenyl-
      P093	103-85-5	Thiourea, phenyl-
      P185	26419-73-8	Tirpate
      P123	8001-35-2	Toxaphene
      P118	75-70-7	Trichloromethanethiol
      P119	7803-55-6	Vanadic acid, ammonium salt
      P120	1314-62-1	Vanadium oxide V2O5
      P120	1314-62-1	Vanadium pentoxide
      P084	4549-40-0	Vinylamine, N-methyl-N-nitroso-
      P001	181-81-2	Warfarin, & salts, when present at concentrations greater than 0.3 percent
      P121	557-21-1	Zinc cyanide
      P121	557-21-1	Zinc cyanide Zn(CN)2
      P205	137-30-4	Zinc, bis(dimethylcarbamodithioato-S,S')-
      P122	1314-84-7	Zinc phosphide Zn3P2, when present at concentrations greater than 10 percent (R,T)
      P205	137-30-4	Ziram

      ____ ¹CAS number given for parent compound only.

   6. (6) The commercial chemical products, manufacturing chemical intermediates, or off- specification commercial chemical products referred to in paragraphs (1) through (4) of this subdivision, are identified as toxic waste (T) unless otherwise designated and are subject to the small quantity generator exclusion defined in section 371.1(f)(1) and (7) of this Part. (Note: For the convenience of the regulated community, the primary hazardous properties of these materials have been indicated by the letters T [Toxicity], R [Reactivity], I [Ignitability] and C [Corrosivity]. Absence of a letter indicates that the compound is only listed for toxicity. These wastes and their corresponding EPA hazardous waste numbers are:

      EPA	Chemical	Substance
      hazardous	abstracts No.
      waste No.
      U394	30558-43-1	A2213
      U001	75-07-0	Acetaldehyde (I)
      U034	75-87-6	Acetaldehyde, trichloro-
      U187	62-44-2	Acetamide, N-(4-ethoxyphenyl)-
      U005	53-96-3	Acetamide, N-9H-fluoren-2-yl-
      U240	194-75-7	Acetic acid, (2,4-dichlorophenoxy)-, salts & esters
      U112	141-78-6	Acetic acid ethyl ester (I)
      U144	301-04-2	Acetic acid, lead(2+) salt
      U214	563-68-8	Acetic acid, thallium(1+) salt
      See F027	93-76-5	Acetic acid, (2,4,5-trichlorophenoxy)-
      U002	67-64-1	Acetone (I)
      U003	75-05-8	Acetonitrile (I,T)
      U004	98-86-2	Acetophenone
      U005	53-96-3	2-Acetylaminofluorene
      U006	75-36-5	Acetyl chloride (C,R,T)
      U007	79-06-1	Acrylamide
      U008	79-10-7	Acrylic acid (I)
      U009	107-13-1	Acrylonitrile
      U011	61-82-5	Amitrole
      U012	62-53-3	Aniline (I,T)
      U136	75-60-5	Arsinic acid, dimethyl-
      U014	492-80-8	Auramine
      U015	115-02-6	Azaserine
      U010	50-07-7	Azirino [2′,3′: 3,4]pyrrolo[1,2-a]indole-4,7-dione, 6-amino- 8-[[(aminocarbonyl) oxy] methyl] -1,1a,2,8a,8b-hexahydro- 8a- methoxy-5-methyl-, [1aS- (1aalpha, 8beta, 8aalpha,8balpha)]-
      U280	101-27-9	Barban
      U278	22781-23-3	Bemdocarb
      U364	22961-82-6	Bendiocarb phenol
      U271	17804-35-2	Benomyl
      U157	56-49-5	Benz [j] aceanthrylene, 1,2-dihydro-3-methyl-
      U016	225-51-4	Benz[c]acridine
      U017	98-87-3	Benzal chloride
      U192	23950-58-5	Benzamide, 3, 5-dichloro-N- (1,1-dimethyl-2-propynyl) -
      U018	56-55-3	Benz[a]anthracene
      U094	57-97-6	Benz[a]anthracene, 7,12-dimethyl-
      U012	62-53-3	Benzenamine (I,T)
      U014	492-80-8	Benzenamine, 4,4′ -carbonimidoylbis[N,N-dimethyl-
      U049	3165-93-3	Benzenamine, 4-chloro-2-methyl-, hydrochloride
      U093	60-11-7	Benzenamine, N,N-dimethyl-4- (phenylazo)-
      U328	95-53-4	Benzenamine, 2-methyl-
      U353	106-49-0	Benzenamine, 4-methyl-
      U158	101-14-4	Benzenamine, 4,4′ -methylenebis [2-chloro-
      U222	636-21-5	Benzenamine, 2-methyl-, hydrochloride
      U181	99-55-8	Benzenamine, 2-methyl-5-nitro-
      U019	71-43-2	Benzene (I,T)
      U038	510-15-6	Benzeneacetic acid, 4-chloro-alpha-(4-chlorophenyl)-alpha- hydroxy-, ethyl ester
      U030	101-55-3	Benzene, 1-bromo-4-phenoxy
      U035	305-03-3	Benzenebutanoic acid, 4-[bis (2- chloroethyl) amino] -
      U037	108-90-7	Benzene, chloro-
      U221	25376-45-8	Benzenediamine, ar-methyl-
      U028	117-81-7	1,2-Benzenedicarboxylic acid, bis(2-ethylhexyl) ester
      U069	84-74-2	1,2-Benzenedicarboxylic acid, dibutyl ester
      U088	84-66-2	1,2-Benzenedicarboxylic acid, diethyl ester
      U102	131-11-3	1,2-Benzenedicarboxylic acid, dimethyl ester
      U107	117-84-0	1,2-Benzenedicarboxylic acid, dioctyl ester
      U070	95-50-1	Benzene, 1,2-dichloro-
      U071	541-73-1	Benzene, 1,3-dichloro-
      U072	106-46-7	Benzene, 1,4-dichloro-
      U060	72-54-8	Benzene, 1,1′-(2,2-dichloroethylidene) bis[4-chloro-
      U017	98-87-3	Benzene, (dichloromethyl)-
      U223	26471-62-5	Benzene, 1, 3-diisocyanatomethyl- (R, T)
      U239	1330-20-7	Benzene, dimethyl-(I)
      U201	108-46-3	1,3-Benzenediol
      U127	118-74-1	Benzene, hexachloro-
      U056	110-82-7	Benzene, hexahydro- (I)
      U220	108-88-3	Benzene, methyl-
      U105	121-14-2	Benzene, 1-methyl-2,4-dinitro-
      U106	606-20-2	Benzene, 2-methyl-1,3-dinitro-
      U055	98-82-8	Benzene, (1-methylethyl)- (I)
      U169	98-95-3	Benzene, nitro-
      U183	608-93-5	Benzene, pentachloro-
      U185	82-68-8	Benzene, pentachloronitro-
      U020	98-09-9	Benzenesulfonic acid chloride (C,R)
      U020	98-09-9	Benzenesulfonyl chloride (C,R)
      U207	95-94-3	Benzene, 1,2,4,5-tetrachloro-
      U061	50-29-3	Benzene, 1,1′-(2,2,2-trichloroethylidene) bis[4-chloro-
      U247	72-43-5	Benzene, 1,1,-(2,2,2-trichloroethylidene) bis[4- methoxy-
      U023	98-07-7	Benzene, (trichloromethyl)-
      U234	99-35-4	Benzene, 1,3,5-trinitro-
      U021	92-87-5	Benzidine
      U202	81-07-2	1,2-Benzisothiazol- 3(2H)-one, 1,1-dioxide, & salts
      U203	94-59-7	1, 3-Benzodioxole, 5-(2-propenyl)-
      U141	120-58-1	1, 3-Benzodioxole, 5-(1-propenyl)-
      U090	94-58-6	1,3-Benzodioxole, 5-propyl-
      U278	22781-23-3	1,3-Benzodioxol-4-ol, 2,2-dimethyl-, methyl carbamate
      U364	22961-82-6	1,3-Benzodioxol-4-ol, 2-2-dimethyl-
      U367	1563-38-8	7-Benzofuranol, 2,3-dihydro-2,2-dimethyl-
      U064	189-55-9	Benzo[rst]pentaphene
      U248	181-81-2	2H-1-Benzopyran-2-one, 4-hydroxy-3- (3-oxo-1- phenyl- butyl)-, & salts, when present at concentrations of 0.3 percent or less
      U022	50-32-8	Benzo[a]pyrene
      U197	106-51-4	p-Benzoquinone
      U023	98-07-7	Benzotrichloride (C,R,T)
      U085	1464-53-5	2,2′-Bioxirane
      U021	92-87-5	[1,1′-Biphenyl] -4,4′-diamine
      U073	91-94-1	[1,1′-Biphenyl]-4,4′-diamine, 3,3′-dichloro-
      U091	119-90-4	[1,1′-Biphenyl]-4,4′-diamine, 3,3′-dimethoxy-
      U095	119-93-7	[1,1′-Biphenyl]-4,4′-diamine, 3,3′-dimethyl-
      U225	75-25-2	Bromoform
      U030	101-55-3	4-Bromophenyl phenyl ether
      U128	87-68-3	1, 3-Butadiene, 1,1,2,3,4,4-hexachloro-
      U172	924-16-3	1-Butanamine, N-butyl-N-nitroso-
      U031	71-36-3	1-Butanol (I)
      U159	78-93-3	2-Butanone (I,T)
      U160	1338-23-4	2-Butanone, peroxide (R,T)
      U053	4170-30-3	2-Butenal
      U074	764-41-0	2-Butene, 1,4-dichloro- (I,T)
      U143	303-34-4	2-Butenoic acid, 2-methyl-,7-[[2,3-dihydroxy-2-(1-methoxyethyl) - 3-methyl-1-oxobutoxy] methyl] - 2,3,5,7a-tetrahydro-1H- pyrrolizin-1-yl ester, [1S- [1alpha(Z), 7(2S*,3R*),7aalpha]]-
      U031	71-36-3	n-Butyl alcohol (I)
      U136	75-60-5	Cacodylic acid
      U032	13765-19-0	Calcium chromate
      U238	51-79-6	Carbamic acid, ethyl ester
      U372	10605-21-7	Carbamic acid, 1H-benzimidazol-2-yl,methyl ester
      U271	17804-35-2	Carbamic acid, [1-[(butylamino)carbonyl]-1H- benzimidazol-2-yl]-,methyl ester
      U280	101-27-9	Carbamic acid, (3-chlorophenyl)-,4-chloro-2-butynyl ester
      U409	23564-05-8	Carbamic acid, [1,2-phenylenebis (iminocarbonothioyl)]bis-, dimethyl ester
      U373	122-42-9	Carbamic acid, phenyl-, 1-methylethyl ester
      U178	615-53-2	Carbamic acid, methylnitroso-, ethyl ester
      U097	79-44-7	Carbamic chloride, dimethyl-
      U114	111-54-6	Carbamodithioic acid, 1,2-ethanediylbis-, salts & esters
      U062	2303-16-4	Carbamothioic acid, bis(1-methylethyl)-, S-(2,3- dichloro-2-propenyl) ester
      U389	2303-17-5	Carbamothioic acid, bis(1-methylethyl-,, S(2,3,3-trichloro-2-propenyl) ester
      U387	52888-80-9	Carbamothioic acid, dipropyl-, S- (phenylmethyl) ester
      U279	63-25-2	Carbaryl
      U372	10605-21-7	Carbendazim
      U367	1563-38-8	Carbofuran phenol
      U215	6533-73-9	Carbonic acid, dithallium(1+) salt
      U033	353-50-4	Carbonic difluoride
      U156	79-22-1	Carbonochloridic acid, methyl ester (I,T)
      U033	353-50-4	Carbon oxyfluoride (R,T)
      U211	56-23-5	Carbon tetrachloride
      U034	75-87-6	Chloral
      U035	305-03-3	Chlorambucil
      U036	57-74-9	Chlordane, alpha & gamma isomers
      U026	494-03-1	Chlornaphazin
      U037	108-90-7	Chlorobenzene
      U038	510-15-6	Chlorobenzilate
      U039	59-50-7	p-Chloro-m-cresol
      U042	110-75-8	2-Chloroethyl vinyl ether
      U044	67-66-3	Chloroform
      U046	107-30-2	Chloromethyl methyl ether
      U047	91-58-7	beta-Chloronaphthalene
      U048	95-57-8	o-Chlorophenol
      U049	3165-93-3	4-Chloro-o-toluidine, hydrochloride
      U032	13765-19-0	Chromic acid H2CrO4, calcium salt
      U050	218-01-9	Chrysene
      U051		Creosote
      U052	1319-77-3	Cresol (Cresylic acid)
      U053	4170-30-3	Crotonaldehyde
      U055	98-82-8	Cumene (I)
      U246	506-68-3	Cyanogen bromide (CN)Br
      U197	106-51-4	2, 5-Cyclohexadiene- 1,4-dione
      U056	110-82-7	Cyclohexane (I)
      U129	58-89-9	Cyclohexane, 1,2,3,4,5,6-hexachloro-, (1alpha, 2alpha, 3beta, 4alpha, 5alpha, 6beta) -
      U057	108-94-1	Cyclohexanone (I)
      U130	77-47-4	1, 3-Cyclopentadiene, 1,2,3,4,5,5-hexachloro-
      U058	50-18-0	Cyclophosphamide
      U240	194-75-7	2,4-D, salts & esters
      U059	20830-81-3	Daunomycin
      U060	72-54-8	DDD
      U061	50-29-3	DDT
      U062	2303-16-4	Diallate
      U063	53-70-3	Dibenz[a,h]anthracene
      U064	189-55-9	Dibenzo[a,i]pyrene
      U066	96-12-8	1,2-Dibromo- 3-chloropropane
      U069	84-74-2	Dibutyl phthalate
      U070	95-50-1	o-Dichlorobenzene
      U071	541-73-1	m-Dichlorobenzene
      U072	106-46-7	p-Dichlorobenzene
      U073	91-94-1	3,3′-Dichlorobenzidine
      U074	764-41-0	1,4-Dichloro-2-butene (I,T)
      U075	75-71-8	Dichlorodifluoromethane
      U078	75-35-4	1,1-Dichloroethylene
      U079	156-60-5	1,2-Dichloroethylene
      U025	111-44-4	Dichloroethyl ether
      U027	108-60-1	Dichloroisopropyl ether
      U024	111-91-1	Dichloromethoxy ethane
      U081	120-83-2	2,4-Dichlorophenol
      U082	87-65-0	2,6-Dichlorophenol
      U084	542-75-6	1,3-Dichloropropene
      U085	1464-53-5	1,2:3,4-Diepoxybutane (I, T)
      U395	5952-26-1	Diethylene glycol, dicarbamate
      U108	123-91-1	1,4-Diethyleneoxide
      U028	117-81-7	Diethylhexyl phthalate
      U086	1615-80-1	N,N′-Diethylhydrazine
      U087	3288-58-2	O,O-Diethyl S-methyl dithiophosphate
      U088	84-66-2	Diethyl phthalate
      U089	56-53-1	Diethylstilbesterol
      U090	94-58-6	Dihydrosafrole
      U091	119-90-4	3,3′-Dimethoxybenzidine
      U092	124-40-3	Dimethylamine (I)
      U093	60-11-7	p-Dimethylaminoazobenzene
      U094	57-97-6	7,12-Dimethylbenz[a]anthracene
      U095	119-93-7	3,3′-Dimethylbenzidine
      U096	80-15-9	alpha,alpha-Dimethylbenzylhydroperoxide (R)
      U097	79-44-7	Dimethylcarbamoyl chloride
      U098	57-14-7	1,1-Dimethylhydrazine
      U099	540-73-8	1,2-Dimethylhydrazine
      U101	105-67-9	2,4-Dimethylphenol
      U102	131-11-3	Dimethyl phthalate
      U103	77-78-1	Dimethyl sulfate
      U105	121-14-2	2,4-Dinitrotoluene
      U106	606-20-2	2,6-Dinitrotoluene
      U107	117-84-0	Di-n-octyl phthalate
      U108	123-91-1	1,4-Dioxane
      U109	122-66-7	1,2-Diphenylhydrazine
      U110	142-84-7	Dipropylamine (I)
      U111	621-64-7	Di-n-propylnitrosamine
      U041	106-89-8	Epichlorohydrin
      U001	75-07-0	Ethanal (I)
      U174	55-18-5	Ethanamine, N-ethyl-N-nitroso-
      U404	121-44-8	Ethanamine, N,N-diethyl-
      U394	30558-43-1	Ethanimidothioic acid, 2-(dimethylamino)-N-hydroxy-2-oxo-,methyl ester
      U410	59669-26-0	Ethanimidothioic acid, N,N'-[thiobis[(methylimino)carbonyloxy]]bis-,dimethyl ester
      U155	91-80-5	1,2-Ethanediamine, N,N-dimethyl-N′ -2-pyridinyl- N′- (2-thienylmethyl) -
      U067	106-93-4	Ethane, 1,2-dibromo-
      U076	75-34-3	Ethane, 1,1-dichloro-
      U077	107-06-2	Ethane, 1,2-dichloro-
      U131	67-72-1	Ethane, hexachloro-
      U024	111-91-1	Ethane, 1,1′ - [methylenebis(oxy)]bis[2-chloro-
      U117	60-29-7	Ethane, 1,1′-oxybis-(I)
      U025	111-44-4	Ethane, 1,1′-oxybis[2-chloro-
      U184	76-01-7	Ethane, pentachloro-
      U208	630-20-6	Ethane, 1,1,1,2- tetrachloro-
      U209	79-34-5	Ethane, 1,1,2,2- tetrachloro-
      U218	62-55-5	Ethanethioamide
      U226	71-55-6	Ethane, 1,1,1-trichloro-
      U227	79-00-5	Ethane, 1,1,2-trichloro-
      U359	110-80-5	Ethanol, 2-ethoxy-
      U173	1116-54-7	Ethanol, 2,2′- (nitrosoimino)bis-
      U395	5952-26-1	Ethanol, 2,2'-oxybis-, dicarbamate
      U004	98-86-2	Ethanone, 1-phenyl-
      U043	75-01-4	Ethene, chloro-
      U042	110-75-8	Ethene, (2-chloroethoxy)-
      U078	75-35-4	Ethene, 1,1-dichloro-
      U079	156-60-5	Ethene, 1,2-dichloro-, (E)-
      U210	127-18-4	Ethene, tetrachloro-
      U228	79-01-6	Ethene, trichloro-
      U112	141-78-6	Ethyl acetate (I)
      U113	140-88-5	Ethyl acrylate (I)
      U238	51-79-6	Ethyl carbamate (urethane)
      U117	60-29-7	Ethyl ether (I)
      U114	1111-54-6	Ethylenebisdithiocarbamic acid, salts & esters
      U067	106-93-4	Ethylene dibromide
      U077	107-06-2	Ethylene dichloride
      U359	110-80-5	Ethylene glycol monoethyl ether
      U115	75-21-8	Ethylene oxide (I,T)
      U116	96-45-7	Ethylenethiourea
      U076	75-34-3	Ethylidene dichloride
      U118	97-63-2	Ethyl methacrylate
      U119	62-50-0	Ethyl methanesulfonate
      U120	206-44-0	Fluoranthene
      U122	50-00-0	Formaldehyde
      U123	64-18-6	Formic acid (C,T)
      U124	110-00-9	Furan (I)
      U125	98-01-1	2-Furancarboxaldehyde (I)
      U147	108-31-6	2,5-Furandione
      U213	109-99-9	Furan, tetrahydro-(I)
      U125	98-01-1	Furfural (I)
      U124	110-00-9	Furfuran (I)
      U206	18883-66-4	Glucopyranose, 2-deoxy-2- (3-methyl-3- nitrosoureido) -, D-
      U206	18883-66-4	D-Glucose, 2-deoxy-2-[[(methylnitrosoamino)- carbonyl]amino] -
      U126	765-34-4	Glycidylaldehyde
      U163	70-25-7	Guanidine, N-methyl- N′-nitro-N-nitroso-
      U127	118-74-1	Hexachlorobenzene
      U128	87-68-3	Hexachlorobutadiene
      U130	77-47-4	Hexachlorocyclopentadiene
      U131	67-72-1	Hexachloroethane
      U132	70-30-4	Hexachlorophene
      U243	1888-71-7	Hexachloropropene
      U133	302-01-2	Hydrazine (R,T)
      U086	1615-80-1	Hydrazine, 1,2-diethyl-
      U098	57-14-7	Hydrazine, 1,1-dimethyl-
      U099	540-73-8	Hydrazine, 1,2-dimethyl-
      U109	122-66-7	Hydrazine, 1,2-diphenyl-
      U134	7664-39-3	Hydrofluoric acid (C,T)
      U134	7664-39-3	Hydrogen fluoride (C,T)
      U135	7783-06-4	Hydrogen sulfide
      U135	7783-06-4	Hydrogen sulfide H2S
      U096	80-15-9	Hydroperoxide, 1-methyl-1-phenylethyl- (R)
      U116	96-45-7	2-Imidazolidinethione
      U137	193-39-5	Indeno [1,2, 3-cd] pyrene
      U190	85-44-9	1, 3-Isobenzofurandione
      U140	78-83-1	Isobutyl alcohol (I,T)
      U141	120-58-1	Isosafrole
      U142	143-50-0	Kepone
      U143	303-34-4	Lasiocarpine
      U144	301-04-2	Lead acetate
      U146	1335-32-6	Lead, bis(acetato-O)tetrahydroxytri-
      U145	7446-27-7	Lead phosphate
      U146	1335-32-6	Lead subacetate
      U129	58-89-9	Lindane
      U163	70-25-7	MNNG
      U147	108-31-6	Maleic anhydride
      U148	123-33-1	Maleic hydrazide
      U149	109-77-3	Malononitrile
      U150	148-82-3	Melphalan
      U151	7439-97-6	Mercury
      U152	126-98-7	Methacrylonitrile (I,T)
      U092	124-40-3	Methanamine, N-methyl- (I)
      U029	74-83-9	Methane, bromo-
      U045	74-87-3	Methane, chloro- (I,T)
      U046	107-30-2	Methane, chloromethoxy-
      U068	74-95-3	Methane, dibromo-
      U080	75-09-2	Methane, dichloro-
      U075	75-71-8	Methane, dichlorodifluoro-
      U138	74-88-4	Methane, iodo-
      U119	62-50-0	Methanesulfonic acid, ethyl ester
      U211	56-23-5	Methane, tetrachloro-
      U153	74-93-1	Methanethiol (I,T)
      U225	75-25-2	Methane, tribromo-
      U044	67-66-3	Methane, trichloro-
      U121	75-69-4	Methane, trichlorofluoro-
      U036	57-74-9	4, 7-Methano-lH-indene, 1,2,4,5,6,7,8,8-octachloro- 2,3,3a,4,7,7a-hexahydro-
      U154	67-56-1	Methanol (I)
      U155	91-80-5	Methapyrilene
      U142	143-50-0	1,3,4-Metheno-2H-cyclobuta[cd]pentalen-2-one, 1,1a,3,3a,4,5, 5,5a,5b,6-decachlorooctahydro-
      U247	72-43-5	Methoxychlor
      U154	67-56-1	Methyl alcohol (I)
      U029	74-83-9	Methyl bromide
      U186	504-60-9	1-Methylbutadiene (I)
      U045	74-87-3	Methyl chloride (I,T)
      U156	79-22-1	Methyl chlorocarbonate (I,T)
      U226	71-55-6	Methyl chloroform
      U157	56-49-5	3-Methylcholanthrene
      U158	101-14-4	4,4′-Methylenebis (2-chloroaniline)
      U068	74-95-3	Methylene bromide
      U080	75-09-2	Methylene chloride
      U159	78-93-3	Methyl ethyl ketone (MEK) (I,T)
      U160	1338-23-4	Methyl ethyl ketone peroxide (R,T)
      U138	74-88-4	Methyl iodide
      U161	108-10-1	Methyl isobutyl ketone (I)
      U162	80-62-6	Methyl methacrylate (I,T)
      U161	108-10-1	4-Methyl-2-pentanone (I)
      U164	56-04-2	Methylthiouracil
      U010	50-07-7	Mitomycin C
      U059	20830-81-3	5,12-Naphthacenedione, 8-acetyl-10- [(3-amino-2,3,6-trideoxy) -alpha-L-lyxo-hexopyranosyl)oxy]-7,8,9,10-tetrahydro-6,8, 11-trihydroxy-1-methoxy-, (8S-cis)-
      U167	134-32-7	1-Naphthalenamine
      U168	91-59-8	2-Naphthalenamine
      U026	494-03-1	Naphthalenamine, N,N′-bis(2-chloroethyl)-
      U165	91-20-3	Naphthalene
      U047	91-58-7	Naphthalene, 2-chloro-
      U166	130-15-4	1,4-Naphthalenedione
      U236	72-57-1	2,7-Naphthalenedisulfonic acid, 3,3′-[(3,3′-dimethyl[l,l′-biphenyl]-4,4′-diyl) bis(azo)bis [5-amino-4-hydroxy]-, tetrasodium salt
      U279	63-25-2	1-Naphthalenol, methylcarbamate
      U166	130-15-4	1,4-Naphthoquinone
      U167	134-32-7	alpha-Naphthylamine
      U168	91-59-8	beta-Naphthylamine
      U217	10102-45-1	Nitric acid, thallium(1 +) salt
      U169	98-95-3	Nitrobenzene (I,T)
      U170	100-02-7	p-Nitrophenol
      U171	79-46-9	2-Nitropropane (I,T)
      U172	924-16-3	N-Nitrosodi-n-butylamine
      U173	116-54-7	N-Nitrosodiethanolamine
      U174	55-18-5	N-Nitrosodiethylamine
      U176	759-73-9	N-Nitroso-N-ethylurea
      U177	684-93-5	N-Nitroso-N-methylurea
      U178	615-53-2	N-Nitroso-N-methylurethane
      U179	100-75-4	N-Nitrosopiperidine
      U180	930-55-2	N-Nitrosopyrrolidine
      U181	99-55-8	5-Nitro-o-toluidine
      U193	1120-71-4	1,2-Oxathiolane, 2,2-dioxide
      U058	50-18-0	2H-1,3,2-Oxazaphosphorin- 2-amine, N,N-bis (2-chloroethyl) tetrahydro-, 2-oxide
      U115	75-21-8	Oxirane (I,T)
      U126	765-34-4	Oxiranecarboxyaldehyde
      U041	106-89-8	Oxirane, (chloromethyl)-
      U182	123-63-7	Paraldehyde
      U183	608-93-5	Pentachlorobenzene
      U184	76-01-7	Pentachloroethane
      U185	82-68-8	Pentachloronitrobenzene (PCNB)
      See F027	87-86-5	Pentachlorophenol
      U161	108-10-1	Pentanol, 4-methyl- (I)
      U186	504-60-9	1,3-Pentadiene (I)
      U187	62-44-2	Phenacetin
      U188	108-95-2	Phenol
      U048	95-57-8	Phenol, 2-chloro-
      U039	59-50-7	Phenol, 4-chloro-3-methyl-
      U081	120-83-2	Phenol, 2,4-dichloro-
      U082	87-65-0	Phenol, 2,6-dichloro-
      U089	56-53-1	Phenol, 4,4′- (1,2-diethyl-1,2-ethenediyl)bis-, (E) -
      U101	105-67-9	Phenol, 2,4-dimethyl-
      U052	1319-77-3	Phenol, methyl-
      U132	70-30-4	Phenol, 2,2′-methylenebis [3,4,6-trichloro-
      U411	114-26-1	Phenol, 2-(1-methylethoxy)-, methylcarbamate
      U170	100-02-7	Phenol, 4-nitro-
      See F027	87-86-5	Phenol, pentachloro-
      See F027	58-90-2	Phenol, 2,3,4,6 -tetrachloro-
      See F027	95-95-4	Phenol, 2,4,5-trichloro-
      See F027	88-06-2	Phenol, 2,4,6-trichloro-
      U150	148-82-3	L-Phenylalanine, 4-[bis(2-chloroethyl) amino]-
      U145	7446-27-7	Phosphoric acid, lead(2+) salt (2:3)
      U087	3288-58-2	Phosphorodithioic acid, O,O-diethyl S-methylester
      U189	1314-80-3	Phosphorus sulfide (R)
      U190	85-44-9	Phthalic anhydride
      U191	109-06-8	2-Picoline
      U179	100-75-4	Piperidine, 1-nitroso-
      U192	23950-58-5	Pronamide
      U194	107-10-8	1-Propanamine (I,T)
      U111	621-64-7	1-Propanamine, N-nitroso-N-propyl-
      U110	142-84-7	1-Propanamine, N-propyl- (I)
      U066	96-12-8	Propane, 1,2-dibromo- 3-chloro-
      U083	78-87-5	Propane, 1,2-dichloro-
      U149	109-77-3	Propanedinitrile
      U171	79-46-9	Propane, 2-nitro- (I,T)
      U027	108-60-1	Propane, 2,2′-oxybis[2-chloro-
      U193	1120-71-4	1,3-Propane sultone
      See F027	93-72-1	Propanoic acid, 2- (2,4,5-trichlorophenoxy)-
      U235	126-72-7	1-Propanol, 2,3-dibromo-, phosphate (3:1)
      U140	78-83-1	1-Propanol, 2-methyl- (I,T)
      U002	67-64-1	2-Propanone (I)
      U007	79-06-1	2-Propenamide
      U084	542-75-6	1-Propene, 1,3-dichloro-
      U243	1888-71-7	1-Propene, 1,1,2,3,3,3 -hexachloro-
      U009	107-13-1	2-Propenenitrile
      U152	126-98-7	2-Propenenitrile, 2-methyl- (I,T)
      U008	79-10-7	2-Propenoic acid (I)
      U113	140-88-5	2-Propenoic acid, ethyl ester (I)
      U118	97-63-2	2-Propenoic acid, 2-methyl-, ethyl ester
      U162	80-62-6	2-Propenoic acid, 2-methyl-, methyl ester (I,T)
      U373	122-42-9	Propham
      U411	114-26-1	Propoxur
      U194	107-10-8	n-Propylamine (I,T)
      U083	78-87-5	Propylene dichloride
      U387	52888-80-9	Prosulfocarb
      U148	123-33-1	3,6-Pyridazinedione, 1,2-dihydro-
      U196	110-86-1	Pyridine
      U191	109-06-8	Pyridine, 2-methyl-
      U237	66-75-1	2,4-(1H, 3H)-Pyrimidinedione, 5-[bis(2-chloroethyl)amino]-
      U164	56-04-2	4(1H)-Pyrimidinone, 2,3-dihydro-6-methyl-2-thioxo-
      U180	930-55-2	Pyrrolidine, 1-nitroso-
      U200	50-55-5	Reserpine
      U201	108-46-3	Resorcinol
      U203	94-59-7	Safrole
      U204	7783-00-8	Selenious acid
      U204	7783-00-8	Selenium dioxide
      U205	7488-56-4	Selenium sulfide
      U205	7488-56-4	Selenium sulfide SeS2 (R,T)
      U015	115-02-6	L-Serine, diazoacetate (ester)
      See F027	93-72-1	Silvex (2,4,5-TP)
      U206	18883-66-4	Streptozotocin
      U103	77-78-1	Sulfuric acid, dimethyl ester
      U189	1314-80-3	Sulfur phosphide (R)
      See F027	93-76-5	2,4,5-T
      U207	95-94-3	1,2,4,5- Tetrachlorobenzene
      U208	630-20-6	1,1,1,2- Tetrachloroethane
      U209	79-34-5	1,1,2,2- Tetrachloroethane
      U210	127-18-4	Tetrachloroethylene
      See F027	58-90-2	2,3,4,6- Tetrachlorophenol
      U213	109-99-9	Tetrahydrofuran (I)
      U214	563-68-8	Thallium(I) acetate
      U215	6533-73-9	Thallium (I) carbonate
      U216	7791-12-0	Thallium(I) chloride
      U216	7791-12-0	Thallium chloride TlCl
      U217	10102-45-1	Thallium (I) nitrate
      U218	62-55-5	Thioacetamide
      U410	59669-26-0	Thiodicarb
      U153	74-93-1	Thiomethanol (I,T)
      U244	137-26-8	Thioperoxydicarbonic diamide [(H2N)C(S)]2S2, tetramethyl-
      U409	23564-05-8	Thiophanate-methyl
      U219	62-56-6	Thiourea
      U244	137-26-8	Thiram
      U220	108-88-3	Toluene
      U221	25376-45-8	Toluenediamine
      U223	26471-62-5	Toluene diisocyanate (R,T)
      U328	95-53-4	o-Toluidine
      U353	106-49-0	p-Toluidine
      U222	636-21-5	o-Toluidine hydrochloride
      U389	2303-17-5	Triallate
      U011	61-82-5	1H-1,2,4-Triazol-3-amine
      U226	71-55-6	1,1,1-Trichloroethane
      U227	79-00-5	1,1,2-Trichloroethane
      U228	79-01-6	Trlchloroethylene
      U121	75-69-4	Trichloromonofluoromethane
      See F027	95-95-4	2,4,5-Trichlorophenol
      See F027	88-06-2	2,4,6-Trichlorophenol
      U404	121-44-8	Triethylamine
      U234	99-35-4	1,3,5-Trinitrobenzene (R,T)
      U182	123-63-7	1,3,5-Trioxane, 2,4,6-trimethyl-
      U235	126-72-7	Tris(2,3-dibromopropyl) phosphate
      U236	72-57-1	Trypan blue
      U237	66-75-1	Uracil mustard
      U176	759-73-9	Urea, N-ethyl-N-nitroso-
      U177	684-93-5	Urea, N-methyl-N-nitroso-
      U043	75-01-4	Vinyl chloride
      U248	181-81-2	Warfarin, & salts, when present at concentrations of 0.3 percent or less
      U239	1330-20-7	Xylene (I)
      U200	50-55-5	Yohimban-16- carboxylic acid, 11,17-dimethoxy-18-[(3,4, 5-trimethoxybenzoyl)oxy]-, methyl ester, (3beta, 16beta, 17alpha, 18beta, 20alpha)-
      U249	1314-84-7	Zinc phosphide Zn3P2, when present at concentrations of 10 percent or less

      ____ ¹CAS number given for parent compound only.

      (e) Wastes containing polychlorinated biphenyls (PCBs).

   7. (1) All solid wastes containing 50 parts per million (ppm) by weight (on a dry weight basis for other than liquid wastes) or greater of polychlorinated biphenyls (PCBs) are listed hazardous wastes, excluding small capacitors as defined in paragraph (3) of this subdivision and PCB articles drained in accordance with subparagraphs (2)(ii) and (iii) of this subdivision. PCB articles that contain less than 50 ppm PCBs are not regulated as hazardous waste. Oils in or from electrical equipment whose PCB concentration is unknown, except circuit breakers, reclosers and cable, must be assumed to contain between 50 and 500 ppm PCB and are listed hazardous waste. PCB and PCBs mean any chemical substance that is limited to the biphenyl molecule that has been chlorinated to varying degrees. Any chemical waste, combination of waste, or environmental media that contains less than 50 ppm PCBs are listed hazardous waste only as specifically provided in paragraph (2) of this subdivision. Wastes that may contain PCBs include dielectric fluids, contaminated solvents, waste oil, heat transfer fluids, hydraulic fluids, dredge spoils, and material contaminated as a result of spills. The hazardous code for these PCB wastes shall be toxic waste (T). Environmental media means naturally occurring, non-living substances, including soil, sediment, rock, groundwater, surface water, surface runoff, air, and only such animal and vegetable matters as may be incidentally contained therein (e.g., soil and water bacteria, underground roots, skeletal remains, etc.). These wastes shall have hazardous waste numbers assigned as follows:

      DEC	Waste
      hazardous
      waste number
      B001	PCB oil (concentrated) from transformers, capacitors, etc.
      B002	Petroleum oil or other liquid containing 50 ppm or greater of PCBs, but less than 500 ppm PCBs. This includes oil from electrical equipment whose PCB concentration is unknown, except for circuit breakers, reclosers, rectifiers and cable.
      B003	Petroleum oil or other liquid containing 500 ppm or greater of PCBs.
      B004	PCB articles containing 50 ppm or greater of PCBs, but less than 500 ppm PCBs, excluding small capacitors. This includes oil-filled electrical equipment whose PCB concentration is unknown, except for circuit breakers, reclosers, rectifiers and cable.
      B005	PCB articles, other than transformers, that contain 500 ppm or greater of PCBs, excluding small capacitors.
      B006	PCB transformers. PCB transformers means any transformer that contains 500 ppm PCB or greater.
      B007	Other PCB wastes, including contaminated soil, solids, sludges, clothing, rags and dredge material.
      Note: PCBs are also regulated by 40 CFR part 761. A person must comply with both this Part and 40 CFR part 761 (see section 370.1[e] ot this Title).

   8. (2) Drained PCB articles.

      1. (i) Except as provided in subparagraphs (ii) and (iii) of this paragraph, drained PCB articles containing at least 50 ppm PCBs are regulated as hazardous waste.

      2. (ii) PCB articles, except capacitors, that contain between 50 and 500 ppm PCB, are no longer regulated as PCB listed hazardous waste provided that all free-flowing liquid has been drained from the article. The drained liquid is a listed hazardous waste, as is any solvent used for flushing.

         1. (a) Hydraulic machines containing less than 1,000 ppm PCB are no longer regulated as PCB listed hazardous waste, provided that all free-flowing liquid has been drained from the hydraulic machine. The drained liquid is a liquid hazardous waste, as is any solvent used for flushing.
         2. (b) Hydraulic machines containing 1,000 ppm PCB are no longer regulated as PCB listed hazardous waste, provided that all free-flowing liquid has been drained from the hydraulic machine, and the drained hydraulic machine is flushed with a solvent in which PCBs are readily soluble. The solvent to be used for flushing must contain less than 50 ppm PCB. The drained liquid and the solvent used for flushing are listed hazardous wastes.

         (iii)

   9. (3) Definitions.

      1. (i) PCB article means any manufactured article, other than a PCB container, that contains PCBs and whose surface(s) has been in direct contact with PCBs. PCB article includes capacitors, transformers, electric motors, circuit breakers, reclosers, rectifiers, voltage regulators, switches (including sectionalizers and motor starters), electromagnets, cable, hydraulic machines, pumps, pipes, and any other manufactured item which is formed to a specific shape or design during manufacture, has end use function(s) dependent in whole or in part upon its shape or design during end use, and has either no change of chemical composition during its end use or only those changes of composition which have no commercial purpose separate from that of the PCB article.
      2. (ii) Small capacitor means a capacitor which contains less than 1.36 kg (3 lb.) of dielectric fluid. The following assumptions may be used if the actual weight of the dielectric fluid is unknown. A capacitor whose total volume is less than 1,639 cubic centimeters (100 cubic inches) may be considered to contain less than 1.36 kg (3 lb.) of dielectric fluid and a capacitor whose total volume is more than 3,278 cubic centimeters (200 cubic inches) must be considered to contain more than 1.36 kg (3 lb.) of dielectric fluid. A capacitor whose volume is between 1,639 and 3,278 cubic centimeters may be considered to contain less than 1.36 (3 lb.) of dielectric fluid if the total weight of the capacitor is less than 4.08 kg (9 lb.).

   10. (4) Testing procedures. The procedures in 40 CFR 761.60(g) (see section 370.1[e] of this Title) will be used to determine the concentration of PCBs, unless a petition for equivalent testing or analytical methods is submitted and approved per section 370.3 of this Title.

       (f) Deletion of certain hazardous waste codes following equipment cleaning and replacement.

   11. (1) Wastes from wood preserving processes at plants that do not resume or initiate use of chlorophenolic preservatives will not meet the listing definition of F032 once the generator has met all of the requirements of paragraphs (2) and (3) of this subdivision. These wastes may, however, continue to meet another hazardous waste listing description or may exhibit one or more of the hazardous waste characteristics.

   12. (2) Generators must either clean or replace all process equipment that may have come into contact with chlorophenolic formulations or constituents thereof, including, but not limited to, treatment cylinders, sumps, tanks, piping systems, drip pads, fork lifts, and trams, in a manner that minimizes or eliminates the escape of hazardous waste or constituents, leachate, contaminated drippage, or hazardous waste decomposition products to the ground water, surface water, or atmosphere.

       1. (i) Generators shall do one of the following:

          1. (a) prepare and follow an equipment replacement plan and clean equipment in accordance with this subdivision;
          2. (b) prepare and follow an equipment replacement plan and replace equipment in accordance with this subdivision; or
          3. (c) document cleaning and replacement in accordance with this subdivision, carried out after termination of use of chlorophenolic preservations.

       2. (ii) Cleaning requirements.

          1. (a) Prepare and sign a written equipment cleaning plan that describes:

             1. (1) the equipment to be cleaned;
             2. (2) how the equipment will be cleaned;
             3. (3) the solvent to be used in cleaning;
             4. (4) how solvent rinses will be tested; and
             5. (5) how cleaning residues will be disposed.

          2. (b) Equipment must be cleaned as follows:

             1. (1) remove all visible residues from process equipment; and
             2. (2) rinse process equipment with an appropriate solvent until dioxins and dibenzofurans are not detected in the final solvent rinse.

          3. (c) Analytical requirements.

             1. (1) rinses must be tested by using an appropriate method;
             2. (2) not detected’ means at or below the following lower method calibration limits (MCLs): The 2,3,7,8-TCDD-based MCLB0.01 parts per trillion (ppt), sample weight of 1000 g, IS spiking level of 1 ppt, final extraction volume of 10-50 ΦL (microlitre). For other congenersBmultiply the values by 1 for TCDF/PeCDD/PeCDF, by 2.5 for HxCDD/HxCDF/HpCDD/HpCDF, and by 5 for OCDD/OCDF.
          4. (d) The generator must manage all residues from the cleaning process as F032 waste.

       3. (iii) Replacement requirements.

          1. (a) Prepare and sign a written equipment replacement plan that describes:

             1. (1) the equipment to be replaced;
             2. (2) how the equipment will be replaced; and
             3. (3) how the equipment will be disposed.
          2. (b) The generator must manage the discarded equipment as F032 waste.

       4. (iv) Documentation requirements.

          1. (a) Document that previous equipment cleaning and/or replacement was performed in accordance with this subdivision and occurred after cessation of use of chlorophenolic preservatives.

   13. (3) The generator must maintain the following records documenting the cleaning and replacement as part of the facility's operating record:

       1. (i) the name and address of the facility;
       2. (ii) formulations previously used and the date on which their use ceased in each process at the plant;
       3. (iii) formulations currently used in each process at the plant;
       4. (iv) the equipment cleaning or replacement plan;
       5. (v) the name and address of any persons who conducted the cleaning and replacement;
       6. (vi) the dates on which cleaning and replacement were accomplished;
       7. (vii) the dates of sampling and testing;
       8. (viii) a description of the sample handling and preparation techniques, including techniques used for extraction, containerization, preservation, and chain-of-custody of the samples;
       9. (ix) a description of the tests performed, the date the tests were performed, and the results of the tests;
       10. (x) the name and model numbers of the instrument(s) used in performing the tests;
       11. (xi) QA/QC documentation; and

       12. (xii) the following statement signed by the generator or an authorized representative:

           “I certify under penalty of law that all process equipment required to be cleaned or replaced under subdivision (f) of this section was cleaned or replaced as represented in the equipment cleaning and replacement plan and accompanying documentation. I am aware that there are significant penalties for providing false information, including the possibility of fine or imprisonment.”

(a) General.