Documents for modular buildings and building components shall include the following:

1. (a) Typical details, including:

   1. (1) Methods of installation of modular buildings or building components on foundations or to each other;
   2. (2) Floor plan(s) and elevation(s);
   3. (3) Cross sections specific to the building system necessary to identify major building components;
   4. (4) Details of flashing including material or gauge at openings and penetrations through roofs and subcomponent connections, including weather barriers and roof system underlayment;
   5. (5) Attic access and attic ventilation, if required by code;
   6. (6) Exterior wall, roof, and soffit material;
   7. (7) Interior wall and ceiling material;
   8. (8) Barrier free provisions, if applicable;
   9. (9) Sizes, locations, and types of doors and windows;
   10. (10) Foundation dimensional plans; and
   11. (11) Insulation values and materials;

2. (b) Fire safety details, including:

   1. (1) Details and locations of fire rated assemblies, including reference listing or test report for all:

      1. a. Stairway enclosures;
      2. b. Doors;
      3. c. Walls;
      4. d. Floors;
      5. e. Ceilings;
      6. f. Partitions;
      7. g. Columns;
      8. h. Roof; and
      9. i. Other enclosures;

   2. (2) Details of means of egress, including:

      1. a. Aisles;
      2. b. Exits;
      3. c. Corridors;
      4. d. Passageways;
      5. e. Stairway enclosures; and
      6. f. Handrails and guardrails;
   3. (3) Flame spread and smoke development classification of interior finish materials;
   4. (4) Location of required draftstops, fireblocking, and through-penetration fire-rated assemblies;
   5. (5) Opening protectives in fire resistance rated systems and assemblies; and
   6. (6) Drawings and calculations of fire suppression systems, standpipes, fire alarms, and detection systems, if required;

3. (c) Structural details, including:

   1. (1) Calculations of structural members and test results, except when compliance can be demonstrated through code tables, product manufacturer handbooks, and listing document;
   2. (2) Details of structural elements, including framing, spacing, size, and connections;
   3. (3) Grade, type, and specifications of materials;
   4. (4) Schedule of roof, floor, wind, and seismic loads on which design is based;
   5. (5) Column loads and column schedule; and
   6. (6) Design and calculations of high-wind connections, including required foundation load, as applicable;

4. (d) Mechanical details, including:

   1. (1) Location of all equipment, appliances, and baseboard radiation units;
   2. (2) Equipment and appliance listing and labeling agencies;
   3. (3) Energy conservation calculations, using rescheck, as defined in Saf-C 3302.24;
   4. (4) Make, model number, and input/output rating of all equipment and appliances;
   5. (5) Duct and register locations, sizes, and materials;
   6. (6) Method of providing combustion air, if required; and
   7. (7) Location of flues, vents, and chimneys, clearances from air intakes, combustible materials, and other vents and flues;

5. (e) Plumbing details, including:

   1. (1) Schematic drawing of the:

      1. a. Plumbing layout, including the size of piping, fittings, traps, and vents;
      2. b. Cleanouts and valves; and
      3. c. Gas, water, and drainage systems; and

   2. (2) Plumbing materials, including:

      1. a. Location of all equipment, appliances, and safety controls to be used;
      2. b. Make, model, rating, and capacity of equipment and appliances; and
      3. c. Equipment and appliance listing or labeling agencies; and

6. (f) Electrical details, including:

   1. (1) Service equipment;
   2. (2) Method of grounding service equipment;
   3. (3) Load calculations for service and feeders;
   4. (4) Sizes of branch circuit conductors;
   5. (5) Size, rating and location of main disconnect and over current protective devices; and
   6. (6) Location of outlets, junction boxes, fixtures and appliances.

Source. #5439, eff 7-24-92; ss by #6810, INTERIM, eff 7-25-98, EXPIRES: 11-22-98; ss by #6885, eff 11-18-98;ss by #8741, INTERIM, eff 11-18-06, EXPIRED: 5-17-07 New. #9752, eff 7-9-10 (from Saf-C 3307.03); ss by #12737, eff 3-8-19