The employer shall ensure compliance with the following requirements:

1. (a) All woodworking machinery such as table saws, swing saws, radial saws, band saws, jointers, tenoning machines, boring and mortising machines, shapers, planers, lathes sanders, and veneer cutters, shall be effectively guarded to protect the operator and other employees from hazards inherent to their operation;
2. (b) A power control device shall be provided on each machine to make it possible for the operator to cut off the power to the machine without leaving their position at the point of operation;
3. (c) Power controls and operating controls shall be located within easy reach of the operator while the operator is at their regular work location, making it unnecessary to reach over the cutter to make adjustments. This shall not apply to constant pressure controls used only for setup purposes;
4. (d) Each operating treadle shall be protected against unexpected or accidental tripping;
5. (e) Disconnect switches shall be capable of being locked or tagged in the off position; and

6. (f) On applications where injury to the operator might result if motors were to restart after a power failure, provision shall be made to prevent machines from automatically restarting upon restoration of power.

   Source. #10809, eff 4-9-15 (from Lab 1403.66); ss by #14431, eff 11-22-25, EXPIRES: 11-22-35

   APPENDIX A

   Rule

   Statute

   Lab 1401.01 and Lab 1401.02

   RSA 281-A:64; RSA 273:9; RSA 277:13; RSA 277:15

   Lab 1402.01 – Lab 1402.08

   RSA 281-A:64

   Lab 1402.09

   RSA 281-A:64; RSA 273:9; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1402.10

   RSA 281-A:64

   Lab 1402.11 – Lab 1402.16

   RSA 281-A:64

   Lab 1402.17

   RSA 281-A:64; RSA 273:9; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1402.18

   RSA 281-A:64; RSA 273:9; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1402.19 – Lab 1402.24

   RSA 281-A:64

   Lab 1402.25

   RSA 281-A:64; RSA 277:1-b, V

   Lab 1402.26 – Lab 1402.45

   RSA 281-A:64

   Lab 1403.01 – Lab 1403.03

   RSA 281-A:64

   Lab 1403.04

   RSA 281-A:64; RSA 277:15-a; RSA 277:15-b

   Lab 1403.05 – Lab 1403.29

   RSA 281-A:64; RSA 273:9; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1403.30

   RSA 281-A:64; RSA 273:9; RSA 277:10; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1403.31 – Lab 1403.54

   RSA 281-A:64; RSA 273:9; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1403.55

   RSA 281-A:64; RSA 273:9; RSA 277: 2; RSA 277:3; RSA 277: 4; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1403.56 – Lab 1403.65

   RSA 281-A:64; RSA 273:9; RSA 277:10; RSA277:11; RSA 277:13; RSA 277:15

   Lab 1403.66

   RSA 281-A:64; RSA 273:9; RSA 277:10; RSA 277:11; RSA 277:13; RSA 277:15

   Lab 1403.67 – Lab 1403.70

   RSA 281-A:64; RSA 273:9; RSA 277:10; RSA 277:11; RSA 277:13; RSA 277:15

   APPENDIX B

   Rule

   Title

   Obtain at:

   Lab 1403.62(b)

   Part 6 of the 2009 Edition of the Federal Highway Administration Manual on Uniform Traffic Control Devices (MUTCD) with Revisions 1 and 2, May 2012 approved under Rules 23CFR PART 630, Subpart F, 630.1106 (c), effective January 15, 2010

   The material can be obtained at no cost on the US Department of Transportation Federal Highway Administration’s web site: http://mutcd.fhwa.dot.gov/pdfs/2009/part6.pdf and Links to hard copy publications can be found on their web site at http://mutcd.fhwa.dot.gov/ser-pubs.htm.

   Costs for hard a copy of publication: AASHTO Bookstore - $60.00 for non-members; American Traffic Safety Services Assoc. - $29.70 for non-members ($22.50 for Flash Drive); Institute of Transportation Engineers - $50.00; IMSA $100.00