651 F.2d 747 | C.C.P.A. | 1981
This appeal is from the judgment of the United States Customs Court (now the United States Court of International Trade) in Philipp Overseas, Inc. v. United States, 84 Cust. Ct. 200, C.D. 4859, 496 F. Supp. 273 (1980), sustaining appellee’s complaint and holding that hot rolled stainless steel angles, which were annealed and pickled during the manufacturing process, are properly classified under Item
BACKGROUND
The imported goods are stainless steel angles. They are formed by “hot rolling” a steel billet, cooling it, annealing it (reheat to 1,000° C and cool by quenching in water), straightening (to remove waves created by the rolling process), and “pickling” (dipping the angles into acid solution). The purpose of annealing is to create a uniform and predictable range of physical characteristics in the metal, including corrosion resistance, by uniformly redistributing its chromium content (which had previously been localized after hot rolling in the form of chromium carbide). The pickling step removes the crust or scale which is formed in annealing, insuring that the chromium now located over the entire surface of the metal can combine with oxygen, giving the metal a uniform layer of chromium oxide, which in turn makes it corrosion resistant.
The angles were assessed a duty at 8.5% ad valorum pursuant to classification under 609.86, TSUS, plus additional duties on their chromium and molybdenum content under Items 607.01 and 607.02, respectively, pursuant to Schedule 6, Part 2, Subpart B, headnote 4. Appellee claimed the proper duty to be 0.1 cent/lb. plus 2% ad valorum under 609.82, TSUS. The additional duties on.the chromium and molybdenum content were not contested.
Statutory Provisions
Tariff Schedules of the United States
SCHEDULE 6 — METALS AND METAL PRODUCTS
* * * * * * *
PART 2.-METALS, THEIR ALLOYS, AND THEIR BASIC SHAPES AND FORMS
Part 2 head-notes:
1. This part covers precious metals and base metals (including such metals when they are chemically pure), their alloys, and their so-called basic shapes and forms, and, in addition, covers metal waste and scrap. Unless the context requires otherwise, the provisions of this part apply to the products described by whatever process made (i.e., whether rolled, forged, drawn, extruded, cast or sintered) and whether or not such products have been subjected to treatments to improve the properties or appearance of the metals or to protect them against rusting, corrosion or other deterioration. These treat*45 ments include annealing, tempering, case-hardening and similar heat-treatment or nitriding; descaling, pickling, scraping, scalping and other processes to remove oxidation scale and crust; * * *. [Emphasis ours.]
*******
SUBPART B.-IRON OR STEEL
*******
Subpart B headnotes:
*******
3. Forms and Conditions of Iron or Steel
* * * * - * * *
(j) Angles, shapes, and sections: Products which do not conform completely to the respective specifications set forth herein for blooins, billets, slabs, sheet bars, bars, wire rods, plates, sheets, strip, wire, rails, joint bars, or tie plates, and do not include any tubular products.
*******
Angles, shapes, and sections, all the foregoing, of iron or steel, hot rolled, forged, extruded, or drawn, or cold formed or cold finished, whether or not drilled, punched, or otherwise advanced; sheet piling of iron or steel;
Angles, shapes, and sections; Hot rolled; or, cold formed and weighing over 0.29 pound per linear foot:
Not drilled, not punched, and not otherwise advanced:
*******
[Claimed]
609.82 Alloy iron or 0.1 cents per
steel. lb.+ 2% ad val. + additional duties (see headnote 4)
Drilled, punched or otherwise advanced :
*46 [Classified]
609.86 Alloy iron or 8.5% ad val.
steel. + additional duties (see headnote 4)
ISSUE
The issue is whether the annealing and pickling processes, which are expressly allowed by headnote 1, “unless the context requires otherwise,” exclude the imported angles from classification under Item 609.82 by reason of the language “not otherwise advanced” in the superior heading.
OPINION BELOW
The Customs Court stated it to be
* * * well settled that no step in the creation of an article is at the same time an “advancement” of the article. United States v. Baron Tube Co. et al., 47 CCPA 69, 71, C.A.D. 730 (1960); Commercial Shearing & Stamping Company v. United States, (Guadalupe Industrial Supply Company, Inc., Party-in-Interest), 65 Cust. Ct. 91, 105, C.D. 4060, 317 F. Supp. 750 (1970), aff'd, 59 CCPA.203, C.A.D. 1067, 464 F. 2d 1048 (1972). Moreover, “manipulations after rolling, incident to making the rolled shape merchantable and fit for shipment, do not constitute ‘advance’ within the congressional intent”. American Mannex Corp. v. United States, 56 Cust. Ct. 31, 36, C.D. 2608 (1966).
Since the angles were intended to be corrosion resistant, and commercially acceptable angles could not be produced without annealing and pickling, the court agreed with appellee that the imported angles were not “otherwise advanced” within the meaning of the heading superior to Item 609.86. It further noted that the government’s own witness indicated that “he had never encountered a single order for nonannealed and nonpickled stainless steel angles.”
The court also applied the doctrine of ejusdem generis, “where particular words of description are followed by general terms, the latter refer only to things of a like class with those particularly described,” to reach the same result. “Otherwise advanced” in the statute is preceded by the words “drilled” and “punched.” Stating that annealing and pickling are not ejusdem generis with drilling and punching, the court held that the presumption of correctness of classification had been overcome and that the proper classification was under Item 609.82 as alleged by appellee,
ARGUMENTS ON APPEAL
The government argues that Items 609.86 and 609.82 provide for angles of alloy iron or steel. They do not require the angles to be stain
The government further argues that, in any event, several witnesses have testified that many angles of “alloy iron or steel” are sold hot rolled as rolled without either annealing or pickling. Thus, it is stated, it is clear that annealing or pickling or both are not necessary to produce or sell angles of alloy iron or steel, and that “advanced” must be construed in terms of further processing beyond the minimum required to create the article, i.e., hot rolling, and not in terms of whether the process renders the article commercially acceptable. Appellant states that the court itself noted that annealing and pickling are “not incidental to the rolling” operation and that, despite this, it erroneously referred to non-annealed and non-pickled angles as “semifinished.”
Finally, the government argues that application of the doctrine of ejusdem generis is unwarranted, its use being reserved for those cases where the legislative intent is in doubt or ambiguous. In proposing that the meaning of the language in the heading superior to 609.86 is clear, the government repeats much of its earlier argument.
Appellee agrees with the reasoning of the lower court. Among other things, it states that the government’s argument that the angles should be considered “otherwise advanced” since annealing and pickling are unnecessary to produce certain types of steel angles ignores the fact that the specific types of alloy steel of which the angles were composed, stainless steel types 304 and 316, require annealing and pickling to create a commercially acceptable product. The processes in issue, it is argued, cannot be both steps in creation and advancement.
OPINION
The lower court stated, as previously noted, that no step in the creation of an article can at the same time be an advancement of that article. The question to be resolved, therefore, is whether that “article” is an [angle] * * * of alloy iron or steel” hotrolled as rolled, asthegovernment argues, or a stainless steel angle which conforms to the pickling
Other than for the proposition of law for which it was cited by the lower court, the case of United States v. Baron Tube Co., supra, is not particularly instructive. Baron Tube had imported steel tubes manufactured by (1) hot rolling steel strips to cylindrical shapes with their longitudinal edges abutting in an open seam, (2) closing that open seam with a weld, and (3) removing the rib resulting from the weld. The imports were classified under a section which laid a duty upon “lap-welded, butt-welded, seamecl, or jointed iron or steel tubes, pipes, flues, and stays * * Baron Tube claimed, and the Customs Court agreed, that the proper duty was found in a section relating to certain structural shapes (not specifically referencing tubes) and “all other structural shapes of iron or steel” which are not advanced beyond “hammering, rolling, or casting.” In reversing the decision of the Customs Court, this court stated that “the tubes here are not structural shapes until processing beyond ‘rolling, hammering, or casting’ has been completed.” Thus, although the court noted that “No step required for the creation of a structural shape * * * can, at the same time be an advancement of a structural shape,” it held that the tubes when rolled did not possess the physical properties required to qualify them as structural shapes. This, however, does not help us determine what comprises an angle of “alloy iron or steel.”
The lower court also stated, regarding “commercial acceptability,” that, “manipulations after rolling, incident to making the rolled shape merchantable and fit for shipment, do not constitute ‘advance’ within the congressional intent’,” citing American Mannex Corp. v. United States, supra, and E. Dillingham, Inc. v. United States, 61 Cust. Ct. 33, C.D. 3522 (1968). Those eases dealt with the removal of useless or dangerous excrescences from rolled steel oil well casings, American Mannex, and from axe head forgings, E. Dillingham. The reasoning behind those decisions was that the cutting or grinding of the excrescences were steps required in the creation of the articles involved — to make them merchantable and fit for shipment — and were thus a part of the rolling and forging process. Commercial Shearing & Stamping Co. v. United States, supra at 105, 317 F. Supp. at 760.
The next question we must address in deciding what “article” we are dealing with, therefore, is whether the steps of annealing and pickling are required to make the imported “angles * * * of alloy iron or steel” merchantable, it being clear that the steps are not required to make the angles “fit for shipment.” This case, however, does not present the type of situation found in American Mannex and E. Dillingham, — whether the excision of useless or dangerous excrescences constitutes “advancement” — for the headnote discussion of “basic shapes an 1 forms” of metals and their
We do, however, on the basis of ejusdem generis, conclude that it would be stretching the matter to hold that even though headnote 1 expressly allows annealing and pickling, “Drilled, punched, or otherwise advanced” in the heading superior to Item 609.86 modifies that allowance pursuant to the phrase in headnote 1, “Unless the context requires otherwise.” Drilling and punching are not ejusdem generis with annealing and pickling, and we therefore hold that the context of the heading superior to Item 609.86 is not one which “requires otherwise.” The decision of the lower court is affirmed.
Schedule 6, Part 2, Subpart B, headnotes 2(h)(ii) and 2(h)(iv).
