RSR Corporation appeals a final order of the Occupational Safety and Health Review Commission, pursuant to section 11(a) of the Occupational Safety and Health Act of .1970, 29 U.S.C. § 660(a). RSR challenges the Commission’s finding of a serious violation, 29 U.S.C. § 666(j), of the standards set forth in 29 C.F.R. § 1910.1025(f)(2)(i) and 29 U.S.C. § 654(a)(2) 1 for failure to select and require its employees to wear appropriate protective respirators in accordance with Table II of the Act’s lead standard, 29 C.F.R. § 1910.1025. Though RSR argues that its violation of the lead standard was not a “serious” one within the meaning of the Act, the gist of its defense is an attack on the substantive validity of the lead standard itself. RSR seeks to contest the validity of the Table II respirator standards in this section 11(a) review of an OSHA enforcement proceeding, 29 U.S.C. § 660(a), after participating in the promulgation, 29 U.S.C. § 655(b), and pre-enforcement judicial review, 29 U.S.C. § 655(f), of the lead standard. We hold that RSR, aware of both its violation and present complaint at the time of its earlier challenge to the lead standard, is now barred from mounting this attack on the respirator regulation’s validity. As its other contentions are without merit, we affirm the Commission’s order.
I
RSR is a secondary lead refiner. It has a wholly owned subsidiary in Dallas, Texas, whose operations include battery wrecking. 2 To guard against exposure to resulting airborne lead contaminants, RSR supplied its battery wrecker employees with *296 half-mask respirators. In August and September of 1979, a compliance officer of the Occupational Safety and Health Administration inspected this Dallas plant, including the battery wrecker department. As a result of this inspection and airborne lead concentration tests, OSHA issued a citation and notification of proposed penalties alleging that RSR had committed a serious violation of 29 C.F.R. § 1910.1025(f)(2)(i) for failure to select appropriate respirators from Table II of 29 C.F.R. 1910.1025(f)(2)(i) (Table II).
Under OSHA’s lead standard, 29 C.F.R. 1910.1025, RSR is obligated to reduce its employees’ exposure to airborne lead to fifty micrograms of lead per cubic meter of air, 50 ug/m3 3 averaged over an eight hour period. 4 When engineering and work practice controls are inadequate to reduce the lead contamination to or below this permissible exposure limit, PEL, respirators must be employed. 5 Table II of 29 C.F.R. § 1910.1025(f)(2)(i) lists the generic types of respirators that must be employed at various levels of airborne lead contamination. 6 When the proper respirator is worn, it reduces employee exposure to lead by a designated “protection factor.” The protection factors assigned the respirators specified in Table II are based on the least effective member of each genre of respirator. In August of 1978, RSR supplied its battery wrecker employees with the 9910 paper half-mask respirator, manufactured by the Minnesota Mining and Manufacturing Company (3M). 7
The OSHA airborne lead tests at the battery wrecker division indicated that employee exposure to airborne lead well exceeded the maximum PEL for which the 3M 9910 was rated in Table II. 8 RSR’s own environmental monitoring from February to November 1979 found contamination levels again well exceeding the permissible exposure limit. 9 Blood lead sampling, also *297 conducted as part of RSR’s monitoring program, revealed that a majority of the battery wrecker employees had blood leads in excess of known toxic levels. 10 The inspection found no other deficiencies in RSR’s lead protection practices and the OSHA inspector concluded that the employees’ elevated blood levels could thus only be attributed to the use of deficient respirators. 11
OSHA then issued a citation and notification of proposed penalties, alleging that RSR had committed a serious violation of the airborne lead contaminant standard in that it did not select thé appropriate respirator from Table II. RSR contested the citation. A hearing was held before a Commission administrative law judge at which RSR conceded its technical violation of the standard, but expressed its belief that the 9910 half-mask respirator provided adequate protection for the battery wrecker workers. It based this belief on actual protection tests performed by the respirator’s manufacturer and by RSR itself after the OSHA inspection. 12 The AU found the “on-the-spot inspection results ... entitled to considerably more weight than the after-the-fact test results” and concluded that RSR committed a serious violation of the standard in “view of the known injurious effects of overexposure to airborne lead.”
RSR also challenged the substantive validity of the respirator regulations, contending that wearer acceptance was not considered in the promulgation of Table II 13 , and that the Table’s guidelines were based on protection factors derived from the least effective respirator in a particular class. 14 The AU found that wearer acceptance was considered in devising the standard and that the Table was therefore validly promulgated. 15 On June 17, 1981, the *298 AU affirmed the citation and assessed a monetary penalty. The Commission declined RSR’s petition for discretionary review and the ALJ’s decision became final by operation of law. 29 U.S.C. § 661(i). RSR now appeals. 29 U.S.C. § 660(a).
II
RSR admits it “technically” violated OSHA’s lead standard in providing its battery wrecker employees with respirators inappropriate under Table II for the air lead measured at its Dallas plant, 29 C.F.R. § 1910.1025(f)(2)(i).' It argues, however, that the Secretary’s failure to consider either actual protection factors or wearer acceptance in promulgating the lead standard, rendered the regulation unreasonable and inconsistent with the Act.
The OSHA lead standard, 29 C.F.R. § 1910.1025, was promulgated under the elaborate rulemaking procedures outlined in section 6(b) of the Act, 29 U.S.C. § 655(b). Section 6(b) affords due process safeguards to persons potentially aggrieved by an OSHA regulation by notifying them and providing them an opportunity to comment or object to a proposed standard.
16
Though RSR launched a substantive challenge to Table II for the first time in this section 11(a) review of an enforcement proceeding, 29 U.S.C. § 660(a),
17
it is no stranger to the OSHA lead standard. RSR directly and as a member of industry and trade associations joined in the notice and comment proceedings surrounding the promulgation of the proposed lead regulation.
18
It also participated extensively in the protracted pre-enforcement judicial review of the lead regulation after it issued in November of 1978.
19
Pursuant to section 6(f) of the Act, 29 C.F.R. § 655(f), RSR petitioned for review of the standard in both the Fifth and Second Circuits.
20
These petitions and others were consolidated and transferred to the District of Columbia Circuit.
United Steelworkers of America, AFL-CIO-CLC v. Marshall,
The Secretary urges that RSR should nevertheless, be barred by section 6(f) of the Act, 29 U.S.C. § 655(f), from challenging the substantive validity of Table II in this enforcement proceeding, as it could and should have done so in pre-enforcement review. We agree.
Section 6(f) of the Act states, in part, that:
Any person who may be adversely affected by a standard issued under this section may at any time prior to the sixtieth day after such standard is promulgated file a petition challenging the validity of such standard with the United States court of appeals for the circuit wherein such person resides or has his principal place of business, for a judicial review of such standard.
29 U.S.C. § 655(f). Though section 6(f) is the exclusive vehicle for pre-enforcement review of an OSHA standard, its preclusive reach in contests of validity made in enforcement proceedings is disputed. The Eighth Circuit has held that all procedural challenges to OSHA standards are barred unless brought within section 6(f)’s sixty day review period.
Madison Falls, Inc. v. Marshall,
While recognizing the appeal of the Eighth Circuit’s “policy” approach, both this Circuit and the Ninth have rejected its result.
Deering Milliken, Inc., Unity Plant v. Occupational Safety and Health Review Commission,
We acknowledge the contention that section 6(f), in itself, does not bar an employer from challenging at least the substantive validity of an OSHA regulation in a subsequent enforcement proceeding.
25
We note, however, that those courts permitting such a section 11(a) attack, including our own, have had before them regulations promulgated under the summary procedures of section 6(a), 29 U.S.C. § 655(a). These regulations have been issued without the elaborate notice and comment due process safeguards required by section 6(b).
26
Indeed, the “practical consideration[s]” accompanying the summary promulgation of these regulations formed an essential part of our reasoning in
Deering Milliken.
We there recognized the “potential number” and “technical complexity” of such standards, and acknowledged that “[i]ndustry would
*301
have found it quite burdensome to comb through every 6(a) regulation and object to inappropriate promulgations within sixty days, considering the ‘multitude of regulations [which] could have been promulgated without notice or hearing within two years of the enactment of OSHA.’ ”
RSR, however, was neither “lulled” nor inactive with respect to the section 6(b) lead regulation at issue here. As already noted, it had ample opportunity to participate in both the promulgation and pre-enforcement review of the lead standard. Unlike the employer in
Deering Milliken,
RSR took advantage of both these opportunities for administrative, 29 U.S.C. § 655(b), and judicial, 29 U.S.C. § 655(f), review. If it had challenged Table II’s validity in these earlier proceedings, RSR would undoubtedly be precluded from re-litigating the issue here.
See Ashe v. Swenson,
An agency has an interest in finality and conservation of its resources. It should not be compelled to defend the same regulation against identical attacks in successive enforcement actions, when those challenges could and should have been asserted in the period for pre-enforcement review. Nor should a court be vexed with a multiplicity of section 11(a) review petitions alleging an invalidity that could have earlier been finally resolved. Though the presumption in favor of judicial review is “strong,”
Deering Milliken,
This reading of the Act not only serves the efficiency goals of agencies and courts, but also implements the core concerns of the Act itself. The very objective of OSHA was “to assure so far as possible every working man and woman in the Nation safe and healthful working conditions and to preserve our human resources____” 29 U.S.C. § 651(b). The uncertainty of enforcement may inhibit an employer, like RSR, from complying with a regulation and encourage him to stockpile known challenges to a regulation’s validity until its fortuitous application to his own business, all the while jeopardizing the safety of his employees and thwarting this Congressional purpose. An employer cannot, even in good faith, unilaterally decide that an OSHA standard is arbitrary or unreasonable, and disregard it, rather than raising *302 its invalidity at the earliest opportunity available to him. 28
We therefore hold that when an employer has participated in the rulemaking and pre-enforcement review of an OSHA regulation and could have then asserted either a substantive or procedural challenge to its validity, but did not, and has no excuse for its failure to do so, we will not entertain the challenge in an enforcement proceeding. We recognize that some issues of validity will not gain sufficient definition before actual enforcement.
See American Trucking Association, Inc. v. I.C.C.,
Ill
We turn now to those defenses available only in enforcement proceedings. RSR contends that even if the respirator selection table was validly promulgated, the Commission erred in failing to consider whether compliance with the standard posed a “greater hazard” than noncompliance and in finding RSR’s violation to be a “serious” one within the meaning of the Act. We find both these contentions to be without merit and the Commission’s order to be supported by substantial evidence.
A.
RSR argues that the AU erred in failing to consider whether compliance with Table II posed a greater threat to the battery wrecker employees than noncompliance and continued use of the half-mask respirator. This circuit recognizes “greater hazard” as an affirmative defense to an OSHA citation.
Cleveland Consolidated, Inc. v. Occupational Safety and Health Review Commission,
Section 11(a) of the Act, 29 U.S.C. § 660(a), bars judicial review of any objection not “urged before the Commission” unless such omission is “excused because of extraordinary circumstances.”
30
Given the agency’s right to be afforded the “opportunity to correct its own mistakes,” we will not lightly disregard this jurisdictional prerequisite.
Power Plant Division, Brown & Root, Inc. v. Occupational Safety and Health Review Commission,
We do not believe the Commission was “alerted” to RSR’s “greater hazard” defense. Though RSR’s factual evidence was consistently directed to establishing that the use of its 3M 9910 respirator provided adequate protection and greater safety than that required by Table II, it was put forward solely to demonstrate the substantive invalidity of the Table or the non-serious nature of the violation. Both these challenges focused the Commission’s attention on whether RSR had shown lack of “substantial evidence in the record considered as a whole” to support the AU’s factual and policy determinations. 29 U.S.C. § 655(f).
See Texas Independent Ginners Association v. Marshall,
The Commission did not have evidence before it to rule on the availability of alternative means or the appropriateness of a variance. 31 RSR’s pleadings and petition for discretionary review centered Commission attention on its “promulgation” and “non-serious” defenses. 32 The Commission, then was not sufficiently alerted to the narrow “greater hazard” defense so as to have an opportunity to pass on it. As no showing -of extraordinary circumstance justifying the omission is advanced, 33 we lack jurisdiction to review it.
B.
RSR finally urges this court to find that its “technical” violation of the *304 respirator selection table is “de minimus” and not a “serious” one within the meaning of section 170 of the Act, 29 U.S.C. § 6660. 34 We find, however, that substantial evidence supports the conclusion that a “substantial probability that death or serious physical harm could result from the violation” of which RSR either knew- or could have known “with the exercise of reasonable diligence.” Id.
The OSHA inspection indicated the battery wrecker employees were overexposed to toxic levels of airborne lead. RSR admits that its use of the 3M 9910 respirator at those concentrations violated' Table II standards. The inspection officer evaluated all other aspects of RSR’s lead hygiene program and found them in compliance with applicable regulations. 35 Biological monitoring indicated that over sixty percent of the employees had blood leads exceeding known toxic levels. Thus the Commission finding that the selection of improper respirators caused these elevated levels, and that lead exposure induces toxic effects 36 are supported by substantial evidence and adequately brace the conclusion that RSR’s violation posed a substantial probability of at least serious physical harm. 37
There is also substantial evidence that RSR had “actual or constructive knowledge of the presence of the violation.”
Bunge Corporation v. Secretary of Labor,
Notes
. Section 5(a)(2) of the Occupational Safety and Health Act, 29 U.S.C. §§ 651 et seq., requires employers to comply with the occupational safety and health standards promulgated by the Secretary of Labor. 29 U.S.C. § 654(a)(2).
. This process involves breaking down old battery cases to reclaim usable lead. Eighteen to twenty workers are employed in the battery wrecker division of the Dallas plant.
. Ambient lead concentrations are measured in terms of micrograms of lead per cubic meter of air. (ug/rn3).
. 29 C.F.R. § 1910.1025(c)(1).
. Id. § 1910.1025(e)(2).
. 29 C.F.R. § 1910.1025(f)(2)(i) provides that:
[w]here respirators are required under this section the employer shall select the appropriate respirator or combination of respirators from table II below.
TABLE II — RESPIRATORY PROTECTION FOR LEAD AEROSOLS
Airborne concentration Required respirator of lead or condition of use
Not in excess of 0.5 mg/m3 (lOxPEL). Half mask, air-purifying respirator equipped with high efficiency filters.
Not in excess of 2.5 mg/m3 (50xPEL). Full facepiece, air-purifying respirator with high efficiency filters.
Not in excess of 50 mg/m3 (lOOOxPEL). (1) Any powered, air-purifying respirator with high efficiency filters; or (2) Half-mask supplicd-air respirator operated in positive-pressure mode.
Not in excess of 100 mg/m3 (2000xPEL). Supplied-air respirators with full facc-piccc, hood, helmet, or suit, operated in positive pressure mode.
Airborne concentration Required respirator- or lead or condition Continued of use — Continued
Greater than 100 Full facepiece, self-contained mg/m3, unknown breathing apparatus operated concentration or in positive-pressure mode, fire fighting.
(Footnotes omitted).
. Though the respirator selection table does not, on its face, permit the use of a 3M 9910 respirator, the Secretary granted an administrative stay to permit its use within the class of half-mask respirators. 44 Fed.Reg. 5446 (Jan. 26, 1979).
. Table II assigns half-mask respirators a protection factor of 10, meaning they may be used to protect against a maximum of 10 times the 50 ug/m3 PEL. Full facepiece respirators are therefore required for exposure levels exceeding this 500 ug/m3 level. The OSHA inspection revealed ambient lead levels of up to 11,750 ug/m3 on the day of the inspection, exceeding the PEL by a factor of 235.
. Employers subject to the Act are required to conduct regular environmental exposure monitoring pursuant to 29 C.F.R. § 1910.1025(d). RSR’s own monitoring at the time its battery wrecker employees were outfitted with the 9910 respirator detected ambient leads up to 31,856 ug/m3, more than 600 times the PEL and but one-sixtieth the worker protection mandated by Table II.
. RSR was statutorily required to biologically monitor its employees and conduct periodic blood lead sampling. 29 C.F.R. § 1910.-1025(j)(2). The AU found that while normal human blood leads are 20 micrograms per 100 grams of blood or less (20 ug/100g), over 60% of RSR’s battery wrecker employees had blood leads exceeding 50 ug/100g. He also found that lead manifests its toxic effects on the body at blood levels of 40 ug/100g. RSR failed to notify these employees of the extent of their blood lead contamination as required by 29 C.F.R. § 1910.1025(j)(2)(iv) (employer required to timely notify employees of blood lead results in excess of 40 ug/100g), and received a second uncontested citation for this violation.
. The OSHA inspector found no fault with the plant’s work practice controls after his examination of RSR’s housekeeping procedures, hygiene facilities (showers and changing rooms), lunchroom area, and control of employee smoking practices. See 29 C.F.R. § 1910.1025(g) (protective work clothing and equipment).
. Although the lead regulations require employers to conduct quantitative fit tests to confirm that the respirator selected for a given employee provides at least the minimum protection outlined in Table II, 29 C.F.R. § 1910.-1025(f)(3), RSR apparently failed to conduct such testing until after the OSHA citations. While RSR's after-the-fact quantitative fit tests yielded protection factors of 11 and above, and 3M’s test data showed protection factors in excess of 30, quantitative fit testing only approximates actual protection as it is conducted in a controlled environment and involves standardized movements not necessarily replicating actual working conditions. An employer is therefore required to, allow a twenty percent margin for inaccuracy in his monitoring results. 29 C.F.R. § 1910.1025(d)(9). RSR’s own expert testified that no half-mask respirator should be accorded a protection factor greater than 100, i.e., for exposure levels in excess of 5,000 ug/m3.
. RSR contended that the 3M half-mask afforded greater comfort and communicative ability than the full facepiece respirator required by Table II, increasing wearing time and providing greater protection.
. A more reasonable standard, it suggests, would be one based on individual quantitative fit testing and an employer's subjective judgment regarding the actual protection provided by a particular respirator model. RSR apparently failed to meet even this proposed standard, however, as no such quantitative fit testing was ever performed before selecting the 3M 9910 respirator for the battery wrecker employees.
. The AU cited the lead regulation's quantitative fit test requirement, 29 C.F.R. § 1910.-1025(f)(3), and the 4.4 hour a day limitation on wearing time, 29 C.F.R. § 1910.1025(f)(1)(i), in concluding that "wearer acceptance ... necessarily had to be considered when the standard was devised.” We note, in addition, that the preamble to the respiratory protection regulation indicates the Secretary carefully considered evidence of wearer acceptance and the prob *298 lems, detailed by RSR, commonly associated with workplace respirators, in adopting Table II. 43 Fed.Reg. 52,992 (1978).
. 29 U.S.C. § 655(b) details the procedures the Secretary must follow in promulgating, modifying, or revoking, any occupational safety and health standard. Such procedures include possible recommendations from an OSHA advisory committee, § (b)(1); publication of the proposed rule in the Federal Register, § (b)(2); and affording interested parties a chance to comment, Id.; file written objections, and request public hearings thereon, § (b)(3).
The Secretary must comply with additional requirements in promulgating standards dealing with "toxic materials or harmful physical agents” such as airborne lead. 29 U.S.C. § 655(b)(5). Section 6(b)(5) requires, for example, that the Secretary base toxic standards on the "best available evidence” including "research, demonstrations, experiments, and such other information as may be appropriate.” He is also directed to consider “the latest available scientific data in the field, the feasibility of the standards, and experience gained under this and other health and safety laws”; and express the standard "in terms of objective criteria and of the performance desired.”
Id.; see Industrial Union Department, AFL-CIO v. American Petroleum Institute,
. 29 U.S.C. § 660(a) provides in part:
Any person adversely affected or aggrieved by an order of the Commission issued under subsection (c) of section 659 of this title may obtain a review of such order in any United States court of appeals for the circuit in which the violation is alleged to have occurred or where the employer has its principal office, or in the Court of Appeals for the District of Columbia Circuit, by filing in such court within sixty days following the issuance of such order a written petition praying that the order be modified or set aside.
. OSHA gave the required notice of this proposed rulemaking in 1975, "Occupational Exposure to Lead: Proposed Rulemaking,” 40 Fed. Reg. 45933 (Oct. 3, 1975).
. 43 Fed.Reg. 52952, 53007 (Nov. 14, 1978).
. RSR Corp. v. OSHA, No. 79-1089 (5th Cir., petition for review filed Jan. 10, 1979) (transferred to D.C.Cir., No. 79-1146, Feb. 2, 1979); National Association of Recycling Industries, Inland Metals Refinery Co. Inc., Keystone Resources Corporation, and RSR Corporation v. Secretary of Labor, No. 79-4011 (2d Cir., petition for review filed Jan. 12, 1979) (transferred to D.C.Cir., No. 79-1111, Feb. 13, 1979).
. Judge Skelly Wright addressed procedural claims in United. Steelworkers that included bias of the decisionmaker, improper separation of staff functions, improper use of consultants, notice deficiencies and denial of cross-examination. The varied substantive challenges went to the lead standard’s medical provisions, the proper standard of review, permissible exposure limits, and the feasibility of the standard with regard to various industries, including secondary lead refining and battery manufacturing.
. The circuit court stayed the effective date of the challenged provisions pending resolution of the regulation’s validity. The Supreme Court issued a similar stay on December 8, 1979. The unchallenged respirator provisions, however, became effective by court order on March 1, 1979.
. We stated:
This Circuit has consistently held that "[a] long-standing and strong presumption exists that action taken by a federal agency is reviewable in federal court.” Save The Bay, Inc. v. Administrator of EPA, 556 F.2d 1282, 1293 (5th Cir.1977). "A statute must demonstrate clear and convincing evidence of an intent to preclude judicial review before courts will cut off an aggrieved party's right to be heard.” *300 Gallo v. Mathews,538 F.2d 1148 , 1151 (5th Cir.1976). See Consolidated-Tomoka Land Company v. Butz,498 F.2d 1208 , 1209 (5th Cir.1974). This position is consistent with the Supreme Court's mandate in Abbott Laboratories v. Gardner,387 U.S. 136 , 140,87 S.Ct. 1507 , 1511,18 L.Ed.2d 681 (1967): "[judicial review of a final agency action by an aggrieved person will not be cut off unless there is persuasive reason to believe that such was the purpose of Congress.”
. The Union Oil court allowed the procedural invalidity of a section 6(a) regulation to be raised as an affirmative defense in an enforcement proceeding. In its search for "express authorization from Congress,” the Ninth Circuit reasoned:
This court, following the Supreme Court’s lead, has consistently held that judicial review of agency action "will not be cut off unless there is persuasive reason to believe that such was the purpose of Congress.” Abbott Laboratories v. Gardner,387 U.S. 136 , 140,87 S.Ct. 1507 , 1511,18 L.Ed.2d 681 (1967). See, e.g., County of Alameda v. Weinberger,520 F.2d 344 , 348 (9th Cir.1975). "There is no presumption against judicial review and in favor of administrative absolutism ... unless that purpose is fairly discernible in the statutory scheme.” Association of Data Processing Service Organizations v. Camp,397 U.S. 150 , 157,90 S.Ct. 827 , 831-32,25 L.Ed.2d 184 (1970).
The Third Circuit also appears to permit claims of substantive or procedural invalidity to be raised in either § 11(a) or § 6(f) review of an’ administrative regulation.
Atlantic & Gulf Stevedores, Inc. v. Occupational Safety and Health Review Commission,
. The legislative history of section 6(f) indicates that while the sixty day post-promulgation period "would be the exclusive method for obtaining pre-enforcement judicial review of a standard, the provision does not foreclose an employer from challenging the validity of a standard during an enforcement proceeding.” S.Rep. No. 91-1282, 91st Cong., 2d Sess., 8,
reprinted in
[1970] U.S.Code Cong. & Ad.News, 5177, 5184. The Eighth Circuit has recognized that "an employer’s right to challenge on
substantive
grounds an allegedly arbitrary or unreasonable regulation" should not be restricted to section 6(f)’s pre-enforcement period.
National Industrial Constructors,
. Section 6(a) was enacted as an interim measure to allow the Secretary, for the first two years after OSHA’s effective date, to circumvent the procedures of the Administrative Procedure Act and summarily promulgate “any national consensus standard” or “any established Federal Standard.” 29 U.S.C. § 655(a). A "national consensus standard” is one that "(1) has been adopted and promulgated by a nationally recognized standards-producing organization under procedures whereby it can be determined by the Secretary that persons interested and affected by the scope or provisions of the standard have reached substantial agreement on its adoption, (2) was formulated in a manner which afforded an opportunity for diverse views to be considered and (3) has been designated as such a standard by the Secretary, after consultation with other appropriate Federal agencies.” 29 U.S.C. § 652(9). An "established Federal standard" is "any operative occupational safety and health standard established by any agency of the United States and presently in effect, or contained in any Act of Congress in force on December 29, 1970." 29 U.S.C. § 652(10).
. The purpose of the section 6(a) short-cut was to enable the Secretary to enact "as rapidly as possible” standards that would provide at least a "nationwide minimum level of health and safety.” S.Rep. No. 91-1282, 91st Cong., 2d Sess. 6,
reprinted in
[1970] U.S.Code Cong. & Ad.News 5177, 5182. As the industries were already familiar with such standards and probably had a previous opportunity to comment upon them when they were initially promulgated, the Secretary was allowed to dispense with usual rule-making procedures. Any subsequent modifications to such summary regulations, however, must be accompanied by section 6(b) formalities.
See Union Oil Company of California,
. The Secretary notes the administrative avenues of relief open to RSR before an OSHA citation issues. Even if RSR selected the half-mask respirator in the good faith belief its employees would not wear the full facepiece one required by Table II, it could have alerted the agency of its concerns through a petition to amend the standard, 29 U.S.C. § 655(b), or a petition for á variance, 29 U.S.C. § 655(d). But significantly, while its petition was being decided the workers would enjoy the protection prescribed, at least until it was decided that the employer's proposal was adequate.
. In so holding, we remain faithful to the tenets of
Cohens v. Virginia,
. 29 U.S.C. § 660(a) in part provides that “[n]o objection that has not been urged before the Commission shall be considered by the court, unless the failure or neglect to urge such objection shall be excused because of extraordinary circumstances."
. This court, in
Irwin Steel Erectors,
found it unnecessary to pass upon the propriety of applying the
Russ Kaller
three-prong standards, as there was substantial evidence to support the Commission’s finding that the employer had not met his burden of showing greater danger in compliance.
. In fact, RSR’s petition for discretionary review actually diverted the Commission from ruling on whether compliance was more - hazardous than noncompliance. Though wearer resistance to the full-mask respirator is crucial to RSR’s greater hazard defense, RSR informed the Commission that ”[t]he question is not whether respondent can enforce the wearing of an ‘unaccepted respirator’ but rather whether the Secretary promulgated a standard that is unlawful because it is unnecessary and inappropriate to insure a safe, healthful workplace."
. See supra note 31.
. 29 U.S.C. § 666(j) sets out the statutory requirements for a serious violation under the Act:
[a] serious violation shall be deemed to exist in a place of employment if there is a substantial probability that death or serious physical harm could result from a condition which exists, or from one or more practices, means, methods, operations, or processes which have been adopted or are in use, in such place of employment unless the employer did not, and could not with the exercise of reasonable diligence, know of the presence of the violation.
. See supra note 11 and accompanying text.
. There was uncontradicted testimony that lead exposure could result in damage to the central nervous system, the peripheral nervous system, the reproductive system, and the kidneys.
See also United States Steelworkers v. Marshall,
. A finding of actual injury is not required to establish a serious violation of the statute.
Shaw Construction Inc. v. Occupational Safety and Health Review Commission,
