152 Wis. 488 | Wis. | 1913
The plaintiff was in charge of tbe canning plant when injured, subject to the direction of the manager •of the company, who made visits and gave directions weekly.
The machinery was operated by a sixty horse-power gasoline engine. There were six machines in the factory, operated by this engine and used for hulling and vining peas. The plaintiff had charge of the engine and plant and general control in the absence of the manager. The engine room was between twenty-four and thirty feet long and from twelve to fourteen feet wide, extending east and west. The engine stood lengthwise of the room with the cylinder and governor’s gear to the west, the fly-wheel to the east, and the driving shaft on the south side as the engine stood in the room. This shaft transmitted the power. There was a space of about three feet between the south wall and the engine. The cylinder of the engine was from three to three and one-half feet long and the outside diameter from eighteen to twenty inches. There was a concrete base under the engine extending about six inches south of the south side of the shaft. The collar on the shaft just to the right of the governor’s gear was a little less than four inches in diameter. The shaft to which the collar was fastened was from one and three-fourths to. two inches in diameter and about three feet from the floor. The collar through which the set-screws passed was from one and one-half to one and three-fourths inches wide and about one inch thick. The heads of the set-screws were a little more than half an inch square. The governor’s gear, collar, and set-screws close to the east side of it were towards the westerly end of the shaft, with a space of about eighteen or twenty inches between the collar and the outside of the fly-wheel. The shaft, when the engine was working, made between ninety-five and one hundred revolutions per minute.
The oil cup which plaintiff was removing when injured was on the easterly end of the cylinder. The bottom of the oil cup was about five feet from the floor, the top of the
Plaintiff was forty-two years of age at the time of tbe trial; bad bad some experience in running a threshing engine and a steam engine, tbe latter in defendant’s plant at Two Eivers, and bad worked for defendant during several seasons prior to tbe time of injury. On tbe 4th day of July, 1908, a messenger was sent to plaintiff by tbe manager with a new kind of oil with instructions to give it a trial right away. While plaintiff was engaged in removing tbe oil cup from tbe top of tbe cylinder for tbe purpose of giving tbe new oil a trial, be was caught on tbe shaft and severely injured. Two photographs of tbe engine are part of tbe record and before us. Tbe south side of tbe shaft is about eight inches from tbe south side of tbe cylinder. A perpendicular line drawn through tbe center of tbe oil cup to the floor would be seventeen or eighteen inches from tbe south side of tbe shaft.
Tbe two main questions involved in this case are (1) whether tbe set-screws were so located as to be dangerous to employees in tbe discharge of their duties; and (2) whether plaintiff was guilty of contributory negligence as a matter of law.
Both of these questions were submitted to tbe jury and found in favor of tbe plaintiff, and tbe findings of the jury were sustained by tbe court below. We are unable to say that tbe trial court was clearly wrong in upholding tbe verdict, therefore we cannot disturb it. Tbe passageway between tbe south side of tbe engine and tbe south wall was necessarily used by plaintiff in tbe discharge of bis duties. Tbe machinery was oiled from that side, some of tbe oil cups or oiling places being in close proximity to the collar and set-screws, and it was necessary to stand quite close to tbe
Under the evidence in this case we think it clear that the question whether the set-screws were so located as to be dangerous to employees in the discharge of their duties was a question for the jury. Miller v. Kimberly & C. Co. 137 Wis. 138, 118 N. W. 536; Kruck v. Wilbur L. Co. 148 Wis. 76, 133 N. W. 1117; Monahan v. Fairbanks-Morse Mfg. Co. 147 Wis. 104, 132 N. W. 983; Monaghan v. Northwestern F. Co. 140 Wis. 457, 122 N. W. 1066; McGinnis v. Northern P. Mills, 147 Wis. 185, 132 N. W. 897, 133 N. W. 22; Koutsky v. Forster-Whitman L. Co. 146 Wis. 425, 131 N. W. 1001; Chopin v. Combined Locks P. Co. 134 Wis. 35, 114 N. W. 95. The set-screws being so located as to be dangerous to employees, it was the duty of the defendant to properly guard them.
But it is strenuously insisted that the plaintiff was guilty of contributory negligence as matter of law, therefore no recovery can be had in this action. There is credible evidence tending to show that the engine room was rather dark, being lighted only by two small windows on the north side; that the plaintiff did not know the collar was fastened to the shaft by set-screws, but supposed it was fastened by a key; that the defendant was very much crowded with work at the factory, and was running very long hours, all day and part of the night; that the day before the injury plaintiff had worked until 11 o’clock at night and commenced work the day of the injury at 3 o’clock in the morning; that he worked from fourteen to twenty-two hours a day; that ordinarily he wore no coat, but this day he was not feeling well and wore one with one or two of the middle buttons fastened; that the large oil cup on top of the cylinder was filled morning, noon, and evening when the engine was not running, but this day he was ordered to try the new oil without delay, and, the engine
Error is assigned on remarks of plaintiff’s counsel to the jury and also as to the form of the second question of the special verdict. We find no prejudicial error under these heads.
By the Court. — The judgment is affirmed.
