18 Wash. 287 | Wash. | 1897
This action was brought to recover damages for personal injuries sustained by plaintiff while employed as a workman in defendant’s foundry. At the time of the injury respondent was engaged in operating machinery for breaking old iron car wheels. A portion of the machinery, consisting of a shaft, was run by a belt about thirty feet in length passing over the outside of a pulley. This shaft and pulley ran very rapidly, making about five-hundred revolutions per minute. It was supported by two iron brackets about eight feet apart attached to the wall. Two iron collars and set screws were placed on the shaft inside the bracket for the purpose of preventing the lateral movement of the shaft. These collars were fastened by means of steel set screws (one on each collar), the heads of which projected five-eighths of an inch. On the 21st of July, 1896, while the machinery was in motion, this belt slipped off the right end of the pulley and fell between the pulley and the right hand bracket. The pulley was about ten feet from the floor. Respondent ascended a ladder, took hold of the belt about a foot below the shaft, and in attempting to lift it upon the pulley the belt was caught between the pulley and the bracket on the head of the set screw and wound about the shaft and the left arm of respondent, throwing him violently to the floor, resulting in the loss of the arm and in other injuries.
The negligence alleged in the complaint may be said to-be the use of defective machinery and the negligent adjustment thereof. The plaintiff had been at work in the same capacity for the defendant about four months in all, prior to the time of the accident. The answer alleges that the injuries were occasioned solely by the carelessness and contributory negligence of the plaintiff in handling and managing the machinery; that the machinery itself and
The gist of the action is negligence, and to entitle respondent to a recovery negligence must be shown. Respondent contends that by placing the collar and set screw inside, instead of outside, the bracket supporting the shaft and failing to countersink the set screw, the construction was faulty and the machine rendered highly dangerous. But the injury resulted, not from any defect in the machinery, but from the attempt to replace the belt while the shaft was revolving with great rapidity, and it is not contended that the belt left the pulley because of any defect— either of the pulley or belt. There was evidence tending to show that the method adopted by respondent to replace the belt would have been safe enough had there been nothing under the belt between the bracket and the end of the pulley but the smooth shaft, but it was rendered extremely dangerous and perilous by reason of the collar and projecting set screw, and the only safe and proper course to pursue in order to replace the belt under the circumstances would have been to notify the engineer to stop or slow down the engine. It was not claimed that there was any defect in the machinery itself, but that it was rendered dangerous by reason of the projecting set screw, and in that respect it could have been rendered safer by countersinking the screw or placing the collar on the outside of the bracket supporting the shaft. It is the duty of the master to furnish to the servant reasonably safe tools, machinery and appliances with which to work, and it is the servant’s duty to
In Ship Building Works v. Nuttall, 119 Pa. St. 149 (13 Atl. 65), the court say:
“ Tbe test is general use. Tried by this test, tbe saw of tbe defendant is such a one as tbe company bad a right to use, because it is such as is commonly used by mill owners.”
In Titus v. Bradford, B. & K. R. Co., supra, one of tbe best considered cases on tbe subject which we have been able to find, it is said:
*291 "Ho man is held by law to a higher degree of sin'll than the fair average of his profession or trade, and the standard of due care is the conduct of the average prudent man. The test of negligence in employers is the same, and however strongly they may he convinced that there is a better or less dangerous way, no jury can he permitted to say that the usual and ordinary way, commonly adopted by those in the same business, is a negligent way for which liability shall he imposed.”
The evidence in this case shows—and the fact is not disputed—that machinery of the character under considera- ■> tion (referring more particularly to the collars and set screws) is in common use in foundries and in other like shops. Assuming, then, that the effort of the respondent to replace the belt while the shaft was in rapid motion would have been safe had the set screw not projected, or if the collar had been on the outside of the bracket, and assuming that respondent was in ignorance of their actual condition or location, was he justified in assuming that there was no projecting set screw or that the collar was outside the bracket? What right had he to assume anything of the kind? If the conditions in these respects were such as commonly exist in other shops and foundries where like machinery is operated, then we think it must he conceded that plaintiff was himself negligent in attempting to replace the'belt under such circumstances. He had no right to assume that the shaft was smooth, and that there was no projecting set screw, or no collar inside the bracket. All machinery is more or less dangerous, and it becomes the duty of persons connected therewith to familiarize and acquaint themselves with the dangers incident thereto. The work in which respondent was engaged did not involve any special risk of which it became appellant’s duty to inform him. The collar and set screw were in plain sight when the machinery was not in action, and it is well nigh in
“Men, when they are working around dangerous machinery, must notice. Their faculties and senses are given them for the purpose of self-preservation, and they must exercise them to a reasonable extent. . . .
“ The dangers in this instance were apparent, and the law is well settled that an employe when he assumes his employment takes the risk of all apparent danger. This was the doctrine announced by this court in Week v. Fremont Mill Co., 3 Wash. 629 (29 Pac. 215), and Jennings v. Tacoma Ry. & Motor Co., Y Wash. 275 (34 Pac. 937), and is the doctrine of common justice and right between employer and employe, and the doctrine of common sense.” Olson v. McMurray Cedar Lumber Co., 9 Wash. 500 (37 Pac. 679).
See, also, Beach, Contributory Negligence, 138; Wormell v. R. R. Co., supra; Bailey, Master’s Liability for Injuries to Servants, p. 169; Nelson, v. Sandford Mills, 89 Me. 219 (36 Atl. 79); Russell v. Tillotson, 140 Mass. 201 (4 N. E. 231).
In this case the slipping of the belt from the pulley was not due to the condition of the set screw, or to the location of the collar upon the shaft, or to any defect in the machinery itself; as already stated, the injury was due to the respondent’s effort to replace the belt. There were two methods by which this could have been done, one of which was perfectly safe and the other beset with peril and danger. The rule is well settled that where there are two
Upon the entire record it appears to us that plaintiff has no cause of action in law upon the facts relied upon, that the request of the appellant for a direction of the verdict should have been granted, that the verdict is contrary to law and to the evidence; and the judgment must be reversed and the cause remanded with direction to the lower court to dismiss.
Scott, O. L, and Dunbar, Anders and Beayis, JJ., concur.