| U.S. Circuit Court for the District of Eastern Wisconsin | Jul 1, 1880
Complainant’s rights depend upon the validity of a patent issued February 10,1874, for an improvement in bail ears used upon pails. One Purches Miles was the alleged inventor of the device in question, and filed an application for a patent November 11, 1873, but the grant of letters patent was made to complainant, Miles having assigned to it his right, title, and interest in said invention. In his specifications the inventor makes this admission: “Wire staples have been employed to form the fastening ej'-es for bails, and these have been driven into the wood with the penetrating points nearly at right angles to the surface, and in use they are liable to pull out by the weight.” He then describes his invention as follows: “My'invention consists in a bail-fastening staple made of wire, with the penetrating ends .cut at such an angle that, in driving them into the wood, they will assume an upward inclination, so that the weight will tend to force such points inwardly, rather than to draw them out, and the bending of the ends in clinching will always be upwardly, thus making a much better and more reliable article than heretofore; and I combine with such fastener a convex metallic washer, to keep the bail from contact with the wood or the paint thereon.”
“ 3. The compound staple-fastening 1), for hails, made with the diagonally-cut penetrating points 2 and 3, loop 4, and body 5; said diagonally-cut points being positioned as set forth, so as to bend upwardly in driving into the wood.
“2. The convex metallic washer E, in combination with the compound bail-fastening staple D, having upwardly penetrating points 2, 3, and loop 4.”
Drawings of the device annexed to the specification show' a staple fastening with two penetrating points or prongs, the upper prong being longer than the lower. The lower prong runs at an acute angle, and the upper prong at an obtuse angle, from the body of the staple; tho 2>J-'ongs, as shown in the drawings, having an upward inclination. The joints are beveled, or cut diagonally on the lower sides, so as to cause them, when driven into the wood, as it is claimed, to turn upwardly and clinch as they are being driven. The washer used in combination with tho staple, to keep the hail from contact with the wood, is an ordinary convex metallic washer. The patent as to the first claim is attacked for want of novelty, and as to the second, because it is, as claimed, for a mere aggregation of parts.
Concerning the second claim I have no doubt. As wo have seen, that claim is for the convex metallic washer in combination with the staple. It is not perceived how the washer can he said to co-operate with the bail car in the production of a common result. It may give greater finish to the pail, and prevent the hail from rubbing and disfiguring tho wood at the point where the bail is fastened to the ear, hut the union of the two devices does not contribute necessarily to one' or the same result, and does not involve invention. The báil ear and the washer perform separate and distinct functions, the distinct office of neither being changed or affected by the operation of the other. The function of the bail ear is to afford a staple fastening for the bail. The presence of the washer does not contribute to nor aid the completeness of the connection between the hail and the bail ear, nor the attachment of the bail ear to the pail. The addition of the washer,
The point is well put in Gidden v. Copeland, 15 O. G. 921, where it is said: “The fact that the knives, the rake, and the binder are respectively subordinate combinations, performing distinct operations, is not fatal to the patentability of a combination of these devices in a harvester, for they all co-operate to produce one definite result. But the combination of a tool chest or feed box with these other elements would not be a patentable combination, because, whatever these appendages may contribute to the production of a convenient or useful harvester, they would not co-operate with the other devices in the production of any one precise result.”
' Plainly, no invention was necessary to combine the washer with the bail ear, and I regard complainant’s patent as to the second claim void, because it is for a mere aggregation of parts which have no common function. In passing upon the -first claim in complainant’s patent it is essential that we ascertain precisely what the patented invention is. The proofs clearly show that prior to complainant’s patent wire staples were employed for the purpose of attaching the handles to pails, and that the use of such staples for that and other purposes was old. In view of the state of the art it is unquestionably necessary, in order to support complainant’s patent, that it be shown that his device presents a feature not before in existence, and which it required invention to •produce. As showing the state of the art defendants have introduced in evidence numerous samples of staples and various patents granted both before and subsequent to complainant’s patent. The Walton patent, granted in 1868, shows a bail ear constructed of wire, bent so as to have an eye, in which the bail is fastened, find two prongs of equal length. This device is unlike complainant’s, as plainly appears on the face of the specifications and claim, because the prongs are intended to be inserted in holes in the sides of the pail, pass
The Krichbaum patent, granted in 1869, discloses a staple having two prongs or points one above the other; but these prongs are not beveled on their lower sides, and evidently are not made to penetrate in an upward direction, nor are they intended to be driven into the wood, as complainant’s device is. The specifications in the patent state that “these ears are secured to the pail by first boring bolos therein, in which the prongs are inserted, which being done they are then clinched down upon the inside.” This device, therefore, does not exhibit the characteristic of the Miles invention, viz., upwardly penetrating points, both arranged to turn in the same direction in the wood in driving.
Miller’s patent, granted in April, 1874, — a caveat for his device having, however, been filed in the patent-office in August, 1878, — shows a staple with two points projecting at directly right angles to the bail ear, each of which points is notched; and in the specifications of the patent it is stated that “the ears are attached to the opposite sides of the bucket, keg, or cask, by driving the projecting portions through tho bucket, the top one being near the rim of tho other, a short distance down the side, and the projecting ends clinched or swaged, the notches facilitating this operation.” The claim in this patent is a broad one, since it is for an article of manufacture, being “the combined bucket, bail and ears, described, the latter constructed of fiat iron, with its lower end rounded to pass through the side of the bucket, and the other end rounded and bent upon itself to form a loop, and terminating in the prong constructed to pass through the side of the bucket.” This patent was re-issued in 1877, and the claim in the re-issued
There is also in evidence the rejected application of one Collins for a patent for an improved bail and tub ear, which application was filed in 1868. A drawing of this device shows a diagonal cut at the point on the upper side of the upper prong of the ear, and a diagonal cut at the point on the lower side of the lower prong. From the description of this device, given by the inventor in his application for a patent, it is evident that it is intended that the two prongs are to be driven entirely through the stave, and then clinched on the inside of the pail, the diagonal cut of the points, as described, being evidently made to facilitate such clinching. Collins’ application was rejected because it was found that his device was anticipated by the patent of Walton, the prongs of both devices being, as before stated, intended to pass entirely through the side of the pail, and clinch on the inner side.
Now, it is probably true that in the particulars in which all these devices, including complainant’s, have features in common, complainant’s patent, if valid, is subordinate to one or more of the patents referred to; but none of these various devices show a construction in form like that of the complainant’s, and none show the lower sides of both points of the staple leveled or cut away so as to cause them to bend upwardly and clinch within the wood when being driven, and this I regard the essence of the Miles invention, if that characteristic of his device can be said to be an invention, and this, I take it, is the whole point of complainant’s case. The proof is abundant that the use of wire staples to form the fastening eyes for bails is, and was at the time complainant’s patent was granted, old. Samples of staples used for various purposes many years have been put in evidence, among which
Now, it is claimed by counsel for defendant that such a state of the art, and such common knowledge with reference to wire staples, existed at the time complainant’s patent was granted, as deprives the patentee of the Miles device of the right to insist that his device was the result of invention; and it is especially urged that, as the Collins device shows one of the points of the staple beveled on the lower side, there was no invention on the part of Miles in making both the points of his staple beveled on the lower side; and since we find that wire staples for hail ears were old when Miles conceived his device, and since, therefore, his invention cannot relate broadly to all kinds of staples, nor even to the simple cutting of a penetrating point diagonally, it becomes a question whether it was invention to devise and make a staple fastening'for bails with both points cut diagonally on the under side, so as to accomplish the purpose designed, viz., to bend the points upwardly in the act of driving.' Plainly, if there is anything patentable in complainant’s device, it is the diagonal cut on the same side of the two points. A claim of novelty based upon the form of the body of the staple is not well founded, because a staple of substantially the same form of body is old, as is shown by exhibits in evidence. A mere reduction in
The principal witness for complainant, who procured for Miles the patent in question, says, in his testimony: “In the said letters patent of complainant the second paragraph makes a very broad admission, to the effect that wire staples have been used for fastening the eyes of bails to pails, and that these staples have been driven into the wood, with penetrating points, nearly at right angles to the surface. I am also aware, and was aware before preparing the papers for said patent, that the penetrating points of staples had been formed in a variety of manners, among which I name the cutting of tlie wires diagonally, the diagonal cut generally being-on the flat side of the staple.”
Other testimony and exhibits in evidence show single-looped staples in use anterior to complainant’s device, with diagonal cuts on the opposite sides of the two points, so that, in driving them, one point would be forced in one direction and the other in an opposite direction. All this shows that the idea of a diagonal cut on the penetrating points of staples was not new with Miles, and that all that he can claim as new with him
The learned counsel for complainant, in argument, relied strongly on the case of Rogers v. Sargent, 7 Blatch. 507, which involved the validity of a patent for a wire staple with corrugated or indented backs or ends. In that case the patent was sustained, and counsel have argued that the invention was merely a corrugated staple, the mere use of a piece of corrugated wire, such as eveiy one had seen long before, but which
Without pursuing the case at bar further, I am of opinion that complainant’s patent must fall, because of. the want of patentability of the device in question.