8 Ct. Cust. 143 | C.C.P.A. | 1917
delivered tbe opinion, of tbe court:
Tbe importations in tbis case are made of steel. Tbeir method of manufacture is stated by a competent witness as follows:
The steel is first cast into square ingots. These square ingots are rolled into round solid blooms.' These blooms are cut up into short lengths,’ and the short lengths are pierced under- a steam hammer, which expands but does not lengthen them. They are then heated up again and rolled in the same type of mill as you would roll solid bars, over a cast-iron plug. ’ After the first rolling they are pickled and ground to remove any surface defects. They are then rolled again to the size desired, after which they are again pickled and annealed and if necessary ground again, after which a piece is cut from each end, which is hardened and fractured, and if those fractures are satisfactory the material is ready for shipment.
The evidence also shows that tbe blooms are about 2 feet long when pierced; that tbe rolling processes thereafter applied cause tbeir lengths to increase, with tbe result that the articles before us are from about 5 to 10 feet long, with inside’diameters varying according to tbe lengths from about- an inch to- 3 or 4 inches., Tbe thickness of the walls also varies according to size, and is not in any one size of exactly uniform thickness. So far as form alone is concerned, these articles may.be described as seamless tubes or pipes. They are finished so far as the rolling processes are concerned, and are not designed to be further processed until they are employed as material in the manufacture of something else.
The importers are the agents in this country for the Swedish manufacturers. They sell practically all they import to one customer, because they are unable' to obtain more than enough for his use.
There is another process employed in producing seamless steel tubes, known as the drawing process, not clearly explained, in the course of which dies.are employed, which probably results in walls more uniform in thickness than the process by which these importations have been produced. The evidence, however, tends to show that it is practically impossible by either process to roll or draw any tube absolutely to size or gauge, and the trade seems to allow a leeway of from 8 or 10 to 15 per cent variation of wall thickness' in these tubes, and sometimes more, according to the requirements of the customer. Some witnesses testified that the tubes were finished because the final processes of manufacture in their present form had been applied, one saying that there was no such thing' as an unfinished tube as it finally came from the rolls. One of importers’, witnesses thought the tubes were not in a finished condition as imported. There is, however, no claim that anything remains to be done to fit them as material for any manufacture for which they are designed or suitable.
Some of the Government’s witnesses testified that merchandise exactly like that here was known in the trade as a tube and at least one that it was regarded as a finished tube.
The question resolves itself to this: Are these seamless steel tubes, finished so far as their present condition is concerned and fit and designed only for use' as material, dutiable as assessed under the provision for “all other iron or steel tubes, finished, not specially provided for in this section,” found in paragraph 127 of the act of 1913? which we here quote:
127. Lap-welded, butt-welded, seamed, or jointed iron or steel tubes, pipes, flues, or stays; cylindrical or tubular tanks or vessels, for bolding gas, liquids, or other material, whether full or empty; flexible metal tubing or hose, not specially provided for in this section, whether covered with wire or other material, or otherwise including any appliances or attachments affixed thereto; welded cylindrical tenaces, tubes or flues made from plate metal, and corrugated, ribbed, or otherwise reenforced against collapsing pressure, and all other non or steel tubes, finished, not specially provided for in this section, 20 per centum ad valorem.
The importers protested, claiming the duty should be assessed under paragraph 110 of the same act as within the provision for “all steels by whatever process made, containing alloys such as * * * chromium * * The Board of General Appraisers overruled
Tbe importers contend first, tbat tbe articles are not tubes within tbe common understanding; second, tbat they are not commercially shown to be tubes, but say tbat, assinning for tbe sake of argument tbat they are tubes, they are not finished tubes in fact or commercially so known. They concede tbat if tbe articles are finished tubes they are more specifically provided for in paragraph 127 than in paragraph 110.
Omitting for tbe present tbe question as to whether these articles are finished steel tubes, we consider whether or not they are tubes in the common acceptation of the term. ■ Restated briefly, they are 5 to 10 feet long, of diameters varying according to the size desired, from about an inch to approximately 3 or 5 inches, are hollow and have an exterior circumference that is practically a circle, while the circumference of the hollow or hole is almost a circle and as nearly so as the processes employed will produce. Nothing more is required to be done to them until used as material for the manufacture of something else.
The importers’ counsel urges that they are not tubes because they are not used for the purposes in. which tubes are usually employed. He points to the fact that as defined by the lexicographers, one meaning of the word “tube” is a “hollow cylinder of any material to convey liquids or .gases,” and says that the use to which these articles are applied is so far foreign thereto that they are not tubes in the common acceptation of the term.
Webster defines a tube as follows:
Tube.—1. A hollow cylinder, of any material, to convey liquids or gases or for some other purpose; a pipe; as, a Are tube; a water tube; a condenser tube (see Condenser, 2e); the tubes of a tubular bridge; a friction tube; the tube of a musical instrument; bronchial tube; a priming tube, etc.
The word “tube” is arbitrarily associated with certain articles or devices not customarily called pipes, and vice versa, although tube and pipe are practically synonymous mechanically; as, iron pipe; glass or rubber tube; gas pipe; boiler tube.
In Knight’s Mechanical Dictionary, when referring to it as made of metal, it is said that a tube is a “metallic pipe of many kinds and uses.”
We think it can not be said that whether or not an article is a tube depends qpon the use to which it is applied. Webster’s definition, which is fairly typical, recognizes “some other purpose” than as a conduit. The uses of steel tubes as material are so common and well known that in the absence of commercial designation we can not say the articles here are not steel tubes within the common understanding of that term. To formulate a definition of “tube” that would exclude them in this case would be to invite trouble in
It may be said in passing that we think, as was held by the board, that the Government has shown by competent evidence that is, not disputed that, commercially speaking, these articles are tubes.
The importers undertake to weaken the effect of this commercial testimony by distinguishing between steel tubes manufactured by the rolling process and by the drawing process in which dies are used. We do not .think the distinction is well founded. It is not a question of processes employed but of results obtained.
' The next question for determination is whether or not these tubes are finished tubes within the meaning of paragraph 127. The Government introduced evidence tending to show that they are commercially known as such. Without deciding whether such commercial designation has or has not been established, we think it sufficiently appears that they are finished in fact.
° The record conclusively establishes' that these tubes are not as tubes further processed or designed to be further processed. All manufacturing processes that are necessary to .be applied have been expended and the articles are finished from that .standpoint. Whatever is done to them in manufacturing therefrom ball bearings or anything else is not, so far as appears, for the purpose of perfecting the tubes as such. It is well settled that the finished product of one process of manufacture may become the material of the next in rank. Tide Water Oil Company v. United States (171 U. S., 210), United States v. Richter (2 Ct. Cust. Appls., 167; T. D. 31680).
If authority were necessary to support the conclusion which we have reached, attention is called to G. A. 4251 (T. D. 20005), decided by the board in September, 1898. This construed the term “all other iron or steel tubes, finished, not specially provided' for,” found in paragraph 152 of the act of 1897, the ancestor paragraph of the one now under consideration, the relevant language of which is identical therewith and is also found in paragraph 151 of the act of 1909. The merchandise, as stated by the board, was weldless steel tubes about 2 inches in diameter and 10 to 18 feet in length. It was assessed as steel tubes, finished, under the paragraph and claimed dutiable under a provision in the first part thereof for welded, seamed, or jointed tubes. It appeared that after importation they were cut up into pieces 6 or 8 inches in length and used as appliances in spinning frames. Their precise condition as imported does not appear. The board, however, said:
* * * But we can give no weight to the importers’ claim that the tubes are unfinished because they are not finished into these appliances. Each tube is manifestly a finished tube in the condition in which imported.
We find that the goods are not welded, seamed, or jointed boiler tubes and that they are finished steel tubes.
This action of the board was reviewed in Circuit Court in Page et al. v. United States (113 Fed., 1006), where it was said by Coxe, Judge, in substance that'the board had found upon testimony that the articles in question were drawn steel tubes, finished, that additional evidence had been taken in Circuit Court, that while ordinarily upon a question of fact the findings of the board would not be reversed unless wholly unsupported by the .proof or clearly against the weight of evidence, the additional testimony taken had not eliminated the fact that the issue still depended upon conflicting testimony and the court said “* * * after considering the testimony, it concurs with the conclusion of fact reached by the board.''’ The judgment of the board was affirmed. This implied an affirmance of its conclusion that the tubes were not unfinished because not finished into the appliances in the manufacture of which they were ultimately used. See also G. A. 3236 (T. D. 16483) relating to tubes for umbrella frames.
We think upon this record the merchandise here is in fact a finished steel tube within the meaning of paragraph 127 and therefore that the judgment of the board ought to be, and it is, affirmed.